# INITIAL MODEL
maestro.perturb_model = true

# PROBLEM SIZE
geometry.prob_lo     =  0.0    0.0
geometry.prob_hi     =  1.0  1.0

# BOUNDARY CONDITIONS
# 0 = Interior   3 = Symmetry
# 1 = Inflow     4 = Slipwall
# 2 = Outflow    5 = NoSlipWall
maestro.lo_bc = 0 0
maestro.hi_bc = 0 0
geometry.is_periodic =  1 1 0

# VERBOSITY
maestro.maestro_verbose              = 1       # verbosity

# DEBUG FOR NAN
amrex.fpe_trap_invalid = 1       # floating point exception

# GRIDDING AND REFINEMENT
amr.n_cell             = 128 128
amr.max_grid_size      = 128
amr.max_level          = 0       # maximum level number allowed
maestro.regrid_int     = 2       # how often to regrid
amr.ref_ratio          = 2 2 2 2 # refinement ratio
amr.blocking_factor    = 8       # block factor in grid generation
amr.refine_grid_layout = 0       # chop grids up into smaller grids if nprocs > ngrids

# TIME STEPPING
maestro.max_step  = 5
maestro.stop_time = 1.0
maestro.cfl       = 0.8    # cfl number for hyperbolic system
                           # In this test problem, the velocity is
		           # time-dependent.  We could use 0.9 in
		           # the 3D test, but need to use 0.7 in 2D
		           # to satisfy CFL condition.
maestro.init_shrink = 0.1e0

# ALGORITHMIC OPTIONS
maestro.evolve_base_state = false
maestro.do_initial_projection = false
maestro.init_divu_iter        = 0
maestro.init_iter             = 1

maestro.do_sponge = 0
maestro.sponge_center_density = 3.e6
maestro.sponge_start_factor = 10.e0
maestro.sponge_kappa = 10.e0

maestro.use_thermal_diffusion = false
maestro.use_delta_gamma1_term = false

# PLOTFILES
maestro.plot_base_name  = incomp_shear_jet_2d_plt    # root name of plot file
maestro.plot_int   = 5      # number of timesteps between plot files
maestro.plot_deltat = 10000

# CHECKPOINT
maestro.check_base_name = incomp_shear_jet_2d_chk
maestro.chk_int         = -1

# tolerances for the initial projection
maestro.eps_init_proj_cart = 1.e-12
maestro.eps_init_proj_sph  = 1.e-10
# tolerances for the divu iterations
maestro.eps_divu_cart      = 1.e-12
maestro.eps_divu_sph       = 1.e-10
maestro.divu_iter_factor   = 100.
maestro.divu_level_factor  = 10.
# tolerances for the MAC projection
maestro.eps_mac            = 1.e-10
maestro.eps_mac_max        = 1.e-8
maestro.mac_level_factor   = 10.
maestro.eps_mac_bottom     = 1.e-3
# tolerances for the nodal projection
maestro.eps_hg             = 1.e-11
maestro.eps_hg_max         = 1.e-10
maestro.hg_level_factor    = 10.
maestro.eps_hg_bottom      = 1.e-4

# HYDRODYNAMICS options
maestro.anelastic_cutoff_density = 1.e-10
maestro.base_cutoff_density = 1.e-10
maestro.grav_const = 0.0e0
maestro.beta0_type = 3
maestro.do_smallscale = true
maestro.ppm_type = 0

# EOS parameters
maestro.small_temp = 1.e-10
maestro.small_dens = 1.e-10

# BURNING parameters
maestro.do_burning = false

# OMP settings
amrex.regtest_reduction = 1

# GPU parameters 
maestro.deterministic_nodal_solve = true

# override the default values of the probin namelist values here
problem.yt = 0.0333333333333e0
problem.delx = 0.05e0
problem.rho_base = 1.0e0
problem.p_base = 1.0e0

# Note that some of the parameters in this
# namelist are specific to the default EOS,
# network, and/or integrator used in the
# makefile. If you try a different set of
# microphysics routines be sure to check that
# the parameters in here are consistent.

#conductivity.const_conductivity = 1.0e0