Initializing AMReX (26.04-113-g05a28aa730e4)... MPI initialized with 4 MPI processes MPI initialized with thread support level 0 AMReX (26.04-113-g05a28aa730e4) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = model.hse model file = model.hse reading initial model 512 points found in the initial model 6 variables found in the initial model model file mapping, level: 0 dr of MAESTRO base state = 781250.000000 dr of input file data = 781250.000000 maximum radius (cell-centered) of input model = 399609375.000000 setting r_cutoff to 330 radius at r_cutoff 258203125 Maximum HSE Error = 0.001041 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_convect_2d_pltInitData after InitData inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.235268685 inner sponge: r_sp , r_tp : 219921875, 296484375 Doing initial projection Calling nodal solver MLMG: Initial rhs = 6.126516885e+10 MLMG: Initial residual (resid0) = 6.126516885e+10 MLMG: Final Iter. 7 resid, resid/bnorm = 0.002288818359, 3.735921083e-14 MLMG: Timers: Solve = 0.064951268 Iter = 0.062735732 Bottom = 0.000368093 Done calling nodal solver Writing plotfile test_convect_2d_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.235234562 Call to firstdt for level 0 gives dt_lev = 0.3657871977 Multiplying dt_lev by init_shrink; dt_lev = 0.03657871977 Minimum firstdt over all levels = 0.03657871977 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 3859584340 MLMG: Initial residual (resid0) = 3859584340 MLMG: Final Iter. 6 resid, resid/bnorm = 0.0004867911339, 1.261252744e-13 MLMG: Timers: Solve = 0.052201042 Iter = 0.050639133 Bottom = 0.000288263 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.3547800905 Minimum estdt over all levels = 0.3547800905 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.3547800905 Multiplying dt by init_shrink; dt = 0.03547800905 Writing plotfile test_convect_2d_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.238057657 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 0.03547800905 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.059199332e+10 MLMG: Initial residual (resid0) = 1.059199332e+10 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1071900353, 1.011991153e-11 MLMG: Timers: Solve = 0.022647844 Iter = 0.021002891 Bottom = 0.000415842 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.059199332e+10 MLMG: Initial residual (resid0) = 123656.1826 MLMG: Final Iter. 5 resid, resid/bnorm = 0.2197556028, 2.074733209e-11 MLMG: Timers: Solve = 0.016843707 Iter = 0.015249313 Bottom = 0.00029002 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.424216593e+10 MLMG: Initial residual (resid0) = 2.424216593e+10 MLMG: Final Iter. 6 resid, resid/bnorm = 0.1175193787, 4.847726025e-12 MLMG: Timers: Solve = 0.052179225 Iter = 0.05061734 Bottom = 0.000310192 Done calling nodal solver Timestep 0 ends with TIME = 0.03547800905 DT = 0.03547800905 Timing summary: Advection :0.118482861 seconds MAC Proj :0.046210873 seconds Nodal Proj :0.066793742 seconds Reactions :0.333445382 seconds Misc :0.098818339 seconds Base State :0.000611713 seconds Time to advance time step: 0.670314867 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.233598718 Writing checkpoint 0 after all initialization Writing checkpoint test_convect_2d_chk0000000 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 0.03547800905 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.056987975e+10 MLMG: Initial residual (resid0) = 1.056987975e+10 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1211298667, 1.145990963e-11 MLMG: Timers: Solve = 0.02300902 Iter = 0.021411753 Bottom = 0.000417357 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.056987974e+10 MLMG: Initial residual (resid0) = 1471.876408 MLMG: Final Iter. 4 resid, resid/bnorm = 0.240102473, 2.27157242e-11 MLMG: Timers: Solve = 0.013688851 Iter = 0.011962805 Bottom = 0.000203459 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1599045671 MLMG: Initial residual (resid0) = 1599045671 MLMG: Final Iter. 5 resid, resid/bnorm = 0.1505362988, 9.414133785e-11 MLMG: Timers: Solve = 0.043987273 Iter = 0.042415974 Bottom = 0.000254441 Done calling nodal solver Timestep 1 ends with TIME = 0.03547800905 DT = 0.03547800905 Timing summary: Advection :0.116809376 seconds MAC Proj :0.043251718 seconds Nodal Proj :0.058651947 seconds Reactions :0.332869804 seconds Misc :0.094507517 seconds Base State :0.0005891 seconds Time to advance time step: 0.652199589 Call to estdt for level 0 gives dt_lev = 0.3529259688 Minimum estdt over all levels = 0.3529259688 Call to estdt at beginning of step 2 gives dt =0.3529259688 dt_growth factor limits the new dt = 0.03902580996  Timestep 2 starts with TIME = 0.03547800905 DT = 0.03902580996 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9753119659 MLMG: Initial residual (resid0) = 9753119659 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1276168823, 1.308472435e-11 MLMG: Timers: Solve = 0.022983131 Iter = 0.021375533 Bottom = 0.000386791 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9753119657 MLMG: Initial residual (resid0) = 15754.04191 MLMG: Final Iter. 4 resid, resid/bnorm = 0.5134958738, 5.264939751e-11 MLMG: Timers: Solve = 0.013774817 Iter = 0.012010553 Bottom = 0.000208979 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1020734907 MLMG: Initial residual (resid0) = 1020734907 MLMG: Final Iter. 6 resid, resid/bnorm = 0.008885860443, 8.705355705e-12 MLMG: Timers: Solve = 0.052619829 Iter = 0.051041 Bottom = 0.00030691 Done calling nodal solver Timestep 2 ends with TIME = 0.07450381901 DT = 0.03902580996 Timing summary: Advection :0.117988612 seconds MAC Proj :0.043362862 seconds Nodal Proj :0.067738048 seconds Reactions :0.333327274 seconds Misc :0.098070727 seconds Base State :0.000596306 seconds Time to advance time step: 0.660747386 Call to estdt for level 0 gives dt_lev = 0.3522809739 Minimum estdt over all levels = 0.3522809739 Call to estdt at beginning of step 3 gives dt =0.3522809739 dt_growth factor limits the new dt = 0.04292839095  Timestep 3 starts with TIME = 0.07450381901 DT = 0.04292839095 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9075727538 MLMG: Initial residual (resid0) = 9075727538 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1086936891, 1.197630588e-11 MLMG: Timers: Solve = 0.022792551 Iter = 0.021183222 Bottom = 0.000408322 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9075727536 MLMG: Initial residual (resid0) = 15175.54771 MLMG: Final Iter. 4 resid, resid/bnorm = 0.7519860929, 8.285683874e-11 MLMG: Timers: Solve = 0.013708154 Iter = 0.011915853 Bottom = 0.000205721 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1103382036 MLMG: Initial residual (resid0) = 1103382036 MLMG: Final Iter. 6 resid, resid/bnorm = 0.009425163269, 8.542066996e-12 MLMG: Timers: Solve = 0.052639494 Iter = 0.050955872 Bottom = 0.000312832 Done calling nodal solver Timestep 3 ends with TIME = 0.11743221 DT = 0.04292839095 Timing summary: Advection :0.119369974 seconds MAC Proj :0.042938341 seconds Nodal Proj :0.067759293 seconds Reactions :0.333577084 seconds Misc :0.101155668 seconds Base State :0.000647686 seconds Time to advance time step: 0.665063441 Call to estdt for level 0 gives dt_lev = 0.3519815355 Minimum estdt over all levels = 0.3519815355 Call to estdt at beginning of step 4 gives dt =0.3519815355 dt_growth factor limits the new dt = 0.04722123005  Timestep 4 starts with TIME = 0.11743221 DT = 0.04722123005 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8248850610 MLMG: Initial residual (resid0) = 8248850610 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1091785431, 1.323560678e-11 MLMG: Timers: Solve = 0.023056763 Iter = 0.021462345 Bottom = 0.000409352 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8248850607 MLMG: Initial residual (resid0) = 14473.20863 MLMG: Final Iter. 4 resid, resid/bnorm = 0.3785336591, 4.588926108e-11 MLMG: Timers: Solve = 0.014055821 Iter = 0.01243577 Bottom = 0.000205442 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1153464230 MLMG: Initial residual (resid0) = 1153464230 MLMG: Final Iter. 6 resid, resid/bnorm = 0.01027870178, 8.911157808e-12 MLMG: Timers: Solve = 0.052347677 Iter = 0.050789077 Bottom = 0.000304867 Done calling nodal solver Timestep 4 ends with TIME = 0.16465344 DT = 0.04722123005 Timing summary: Advection :0.120198019 seconds MAC Proj :0.043661575 seconds Nodal Proj :0.067394681 seconds Reactions :0.332905354 seconds Misc :0.10191815 seconds Base State :0.00059158 seconds Time to advance time step: 0.666348526 Call to estdt for level 0 gives dt_lev = 0.3519075579 Minimum estdt over all levels = 0.3519075579 Call to estdt at beginning of step 5 gives dt =0.3519075579 dt_growth factor limits the new dt = 0.05194335306  Timestep 5 starts with TIME = 0.16465344 DT = 0.05194335306 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6944513254 MLMG: Initial residual (resid0) = 6944513254 MLMG: Final Iter. 7 resid, resid/bnorm = 0.08908589184, 1.282824132e-11 MLMG: Timers: Solve = 0.023002429 Iter = 0.021398812 Bottom = 0.000412213 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6944513252 MLMG: Initial residual (resid0) = 13528.23695 MLMG: Final Iter. 4 resid, resid/bnorm = 0.3968143468, 5.714069978e-11 MLMG: Timers: Solve = 0.013941848 Iter = 0.012341305 Bottom = 0.000210017 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1162694978 MLMG: Initial residual (resid0) = 1162694978 MLMG: Final Iter. 6 resid, resid/bnorm = 0.01120948792, 9.640953239e-12 MLMG: Timers: Solve = 0.052452806 Iter = 0.050895657 Bottom = 0.000312413 Done calling nodal solver Timestep 5 ends with TIME = 0.2165967931 DT = 0.05194335306 Timing summary: Advection :0.120462083 seconds MAC Proj :0.043484145 seconds Nodal Proj :0.06715548 seconds Reactions :0.33282406 seconds Misc :0.102224551 seconds Base State :0.000588635 seconds Time to advance time step: 0.666447774 Writing plotfile 5 inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.290108103 Writing checkpoint 5 Writing checkpoint test_convect_2d_chk0000005 Total Time: 6.471337922 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [test_convect_2d_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] [TOP]::amr.plot_file(nvals = 1) :: [test_convect_2d_plt] AMReX (26.04-113-g05a28aa730e4) finalized