Initializing AMReX (26.05-55-g750b74d10a21)... MPI initialized with 4 MPI processes MPI initialized with thread support level 0 AMReX (26.05-55-g750b74d10a21) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = model.hse model file = model.hse reading initial model 512 points found in the initial model 6 variables found in the initial model model file mapping, level: 0 dr of MAESTRO base state = 781250.000000 dr of input file data = 781250.000000 maximum radius (cell-centered) of input model = 399609375.000000 setting r_cutoff to 330 radius at r_cutoff 258203125 Maximum HSE Error = 0.001041 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_convect_2d_pltInitData after InitData inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.262832402 inner sponge: r_sp , r_tp : 219921875, 296484375 Doing initial projection Calling nodal solver MLMG: Initial rhs = 6.126516885e+10 MLMG: Initial residual (resid0) = 6.126516885e+10 MLMG: Final Iter. 7 resid, resid/bnorm = 0.002288818359, 3.735921083e-14 MLMG: Timers: Solve = 0.06482289 Iter = 0.062711254 Bottom = 0.000353979 Done calling nodal solver Writing plotfile test_convect_2d_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.235653348 Call to firstdt for level 0 gives dt_lev = 0.3657871977 Multiplying dt_lev by init_shrink; dt_lev = 0.03657871977 Minimum firstdt over all levels = 0.03657871977 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 3859584340 MLMG: Initial residual (resid0) = 3859584340 MLMG: Final Iter. 6 resid, resid/bnorm = 0.0004867911339, 1.261252744e-13 MLMG: Timers: Solve = 0.052723719 Iter = 0.050821668 Bottom = 0.000285783 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.3547800905 Minimum estdt over all levels = 0.3547800905 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.3547800905 Multiplying dt by init_shrink; dt = 0.03547800905 Writing plotfile test_convect_2d_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.237986023 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 0.03547800905 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.059199332e+10 MLMG: Initial residual (resid0) = 1.059199332e+10 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1071900353, 1.011991153e-11 MLMG: Timers: Solve = 0.022670499 Iter = 0.020942437 Bottom = 0.000409211 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.059199332e+10 MLMG: Initial residual (resid0) = 123656.1826 MLMG: Final Iter. 5 resid, resid/bnorm = 0.2197556028, 2.074733209e-11 MLMG: Timers: Solve = 0.016850006 Iter = 0.015249531 Bottom = 0.000260697 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.424216593e+10 MLMG: Initial residual (resid0) = 2.424216593e+10 MLMG: Final Iter. 6 resid, resid/bnorm = 0.1175193787, 4.847726025e-12 MLMG: Timers: Solve = 0.052236228 Iter = 0.050667027 Bottom = 0.000306422 Done calling nodal solver Timestep 0 ends with TIME = 0.03547800905 DT = 0.03547800905 Timing summary: Advection :0.11930656 seconds MAC Proj :0.046158833 seconds Nodal Proj :0.067015847 seconds Reactions :0.333658716 seconds Misc :0.097132248 seconds Base State :0.000593646 seconds Time to advance time step: 0.669221576 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.233856166 Writing checkpoint 0 after all initialization Writing checkpoint test_convect_2d_chk0000000 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 0.03547800905 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.056987975e+10 MLMG: Initial residual (resid0) = 1.056987975e+10 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1211298667, 1.145990963e-11 MLMG: Timers: Solve = 0.023069123 Iter = 0.021478832 Bottom = 0.000418984 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.056987974e+10 MLMG: Initial residual (resid0) = 1471.876408 MLMG: Final Iter. 4 resid, resid/bnorm = 0.240102473, 2.27157242e-11 MLMG: Timers: Solve = 0.014037458 Iter = 0.012444061 Bottom = 0.000208539 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1599045671 MLMG: Initial residual (resid0) = 1599045671 MLMG: Final Iter. 5 resid, resid/bnorm = 0.1505362988, 9.414133785e-11 MLMG: Timers: Solve = 0.04417824 Iter = 0.042588377 Bottom = 0.000260047 Done calling nodal solver Timestep 1 ends with TIME = 0.03547800905 DT = 0.03547800905 Timing summary: Advection :0.116290975 seconds MAC Proj :0.043661331 seconds Nodal Proj :0.059067748 seconds Reactions :0.331080931 seconds Misc :0.094454715 seconds Base State :0.000595169 seconds Time to advance time step: 0.650641026 Call to estdt for level 0 gives dt_lev = 0.3529259688 Minimum estdt over all levels = 0.3529259688 Call to estdt at beginning of step 2 gives dt =0.3529259688 dt_growth factor limits the new dt = 0.03902580996  Timestep 2 starts with TIME = 0.03547800905 DT = 0.03902580996 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9753119659 MLMG: Initial residual (resid0) = 9753119659 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1276168823, 1.308472435e-11 MLMG: Timers: Solve = 0.022671342 Iter = 0.02106745 Bottom = 0.000382478 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9753119657 MLMG: Initial residual (resid0) = 15754.04191 MLMG: Final Iter. 4 resid, resid/bnorm = 0.5134958738, 5.264939751e-11 MLMG: Timers: Solve = 0.013846633 Iter = 0.012260425 Bottom = 0.000205861 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1020734907 MLMG: Initial residual (resid0) = 1020734907 MLMG: Final Iter. 6 resid, resid/bnorm = 0.008885860443, 8.705355705e-12 MLMG: Timers: Solve = 0.052313956 Iter = 0.050753336 Bottom = 0.000309279 Done calling nodal solver Timestep 2 ends with TIME = 0.07450381901 DT = 0.03902580996 Timing summary: Advection :0.117420011 seconds MAC Proj :0.043088441 seconds Nodal Proj :0.067220095 seconds Reactions :0.328635645 seconds Misc :0.098495608 seconds Base State :0.000604061 seconds Time to advance time step: 0.655103835 Call to estdt for level 0 gives dt_lev = 0.3522809739 Minimum estdt over all levels = 0.3522809739 Call to estdt at beginning of step 3 gives dt =0.3522809739 dt_growth factor limits the new dt = 0.04292839095  Timestep 3 starts with TIME = 0.07450381901 DT = 0.04292839095 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9075727538 MLMG: Initial residual (resid0) = 9075727538 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1086936891, 1.197630588e-11 MLMG: Timers: Solve = 0.022539344 Iter = 0.02094505 Bottom = 0.000396344 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9075727536 MLMG: Initial residual (resid0) = 15175.54771 MLMG: Final Iter. 4 resid, resid/bnorm = 0.7519860929, 8.285683874e-11 MLMG: Timers: Solve = 0.013877455 Iter = 0.01227698 Bottom = 0.000205256 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1103382036 MLMG: Initial residual (resid0) = 1103382036 MLMG: Final Iter. 6 resid, resid/bnorm = 0.009425163269, 8.542066996e-12 MLMG: Timers: Solve = 0.052365495 Iter = 0.050780504 Bottom = 0.00031378 Done calling nodal solver Timestep 3 ends with TIME = 0.11743221 DT = 0.04292839095 Timing summary: Advection :0.118713945 seconds MAC Proj :0.043091607 seconds Nodal Proj :0.067310262 seconds Reactions :0.329988486 seconds Misc :0.101540546 seconds Base State :0.000658016 seconds Time to advance time step: 0.660881099 Call to estdt for level 0 gives dt_lev = 0.3519815355 Minimum estdt over all levels = 0.3519815355 Call to estdt at beginning of step 4 gives dt =0.3519815355 dt_growth factor limits the new dt = 0.04722123005  Timestep 4 starts with TIME = 0.11743221 DT = 0.04722123005 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8248850610 MLMG: Initial residual (resid0) = 8248850610 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1091785431, 1.323560678e-11 MLMG: Timers: Solve = 0.023054244 Iter = 0.021172107 Bottom = 0.000402863 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8248850607 MLMG: Initial residual (resid0) = 14473.20863 MLMG: Final Iter. 4 resid, resid/bnorm = 0.3785336591, 4.588926108e-11 MLMG: Timers: Solve = 0.014432861 Iter = 0.01284551 Bottom = 0.00021025 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1153464230 MLMG: Initial residual (resid0) = 1153464230 MLMG: Final Iter. 6 resid, resid/bnorm = 0.01027870178, 8.911157808e-12 MLMG: Timers: Solve = 0.052452461 Iter = 0.050872146 Bottom = 0.000307041 Done calling nodal solver Timestep 4 ends with TIME = 0.16465344 DT = 0.04722123005 Timing summary: Advection :0.120043894 seconds MAC Proj :0.044028101 seconds Nodal Proj :0.067404884 seconds Reactions :0.330632346 seconds Misc :0.102642459 seconds Base State :0.000593036 seconds Time to advance time step: 0.664989538 Call to estdt for level 0 gives dt_lev = 0.3519075579 Minimum estdt over all levels = 0.3519075579 Call to estdt at beginning of step 5 gives dt =0.3519075579 dt_growth factor limits the new dt = 0.05194335306  Timestep 5 starts with TIME = 0.16465344 DT = 0.05194335306 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6944513254 MLMG: Initial residual (resid0) = 6944513254 MLMG: Final Iter. 7 resid, resid/bnorm = 0.08908589184, 1.282824132e-11 MLMG: Timers: Solve = 0.022701113 Iter = 0.021098871 Bottom = 0.000411821 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6944513252 MLMG: Initial residual (resid0) = 13528.23695 MLMG: Final Iter. 4 resid, resid/bnorm = 0.3968143468, 5.714069978e-11 MLMG: Timers: Solve = 0.013913717 Iter = 0.012300366 Bottom = 0.000206827 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1162694978 MLMG: Initial residual (resid0) = 1162694978 MLMG: Final Iter. 6 resid, resid/bnorm = 0.01120948792, 9.640953239e-12 MLMG: Timers: Solve = 0.052712657 Iter = 0.05113036 Bottom = 0.00032026 Done calling nodal solver Timestep 5 ends with TIME = 0.2165967931 DT = 0.05194335306 Timing summary: Advection :0.120412021 seconds MAC Proj :0.043286971 seconds Nodal Proj :0.067618567 seconds Reactions :0.331749344 seconds Misc :0.10204685 seconds Base State :0.000595909 seconds Time to advance time step: 0.665344577 Writing plotfile 5 inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.286058182 Writing checkpoint 5 Writing checkpoint test_convect_2d_chk0000005 Total Time: 6.512974952 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [test_convect_2d_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] [TOP]::amr.plot_file(nvals = 1) :: [test_convect_2d_plt] AMReX (26.05-55-g750b74d10a21) finalized