Initializing AMReX (26.05-56-gb8117c772be8)... MPI initialized with 4 MPI processes MPI initialized with thread support level 0 AMReX (26.05-56-gb8117c772be8) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = model.hse.cool.coulomb model file = model.hse.cool.coulomb reading initial model 640 points found in the initial model 6 variables found in the initial model model file mapping, level: 0 dr of MAESTRO base state = 562500.000000 dr of input file data = 562500.000000 maximum radius (cell-centered) of input model = 359718750.000000 setting r_cutoff to 365 radius at r_cutoff 205593750 Maximum HSE Error = 0.000061 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile reacting_bubble_3d_pltInitData after InitData inner sponge: r_sp , r_tp : 186468750, 224718750 Time to write plotfile: 2.934178144 inner sponge: r_sp , r_tp : 186468750, 224718750 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.022881021 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile reacting_bubble_3d_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 186468750, 224718750 Time to write plotfile: 2.919782467 Call to firstdt for level 0 gives dt_lev = 0.0004741795139 Multiplying dt_lev by init_shrink; dt_lev = 0.0004741795139 Minimum firstdt over all levels = 0.0004741795139 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 2054.815795 MLMG: Initial residual (resid0) = 2054.815795 MLMG: Final Iter. 7 resid, resid/bnorm = 5.614158027e-10, 2.732195285e-13 MLMG: Timers: Solve = 0.676607511 Iter = 0.654013182 Bottom = 0.00748107 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.1719927642 Minimum estdt over all levels = 0.1719927642 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.1719927642 Multiplying dt by init_shrink; dt = 0.1719927642 Ignoring this new dt since it's larger than the previous dt = 0.0004741795139 Writing plotfile reacting_bubble_3d_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 186468750, 224718750 Time to write plotfile: 2.924527883 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 0.0004741795139 Cell Count: Level 0, 1327104 cells inner sponge: r_sp , r_tp : 186468750, 224718750 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2728631.973 MLMG: Initial residual (resid0) = 2728631.973 MLMG: Final Iter. 9 resid, resid/bnorm = 1.611048356e-05, 5.904234691e-12 MLMG: Timers: Solve = 0.387410343 Iter = 0.372382853 Bottom = 0.00889802 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2728627.792 MLMG: Initial residual (resid0) = 8729.745165 MLMG: Final Iter. 5 resid, resid/bnorm = 0.0002251341939, 8.250820966e-11 MLMG: Timers: Solve = 0.222310105 Iter = 0.207224313 Bottom = 0.004861698 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.157552615e+10 MLMG: Initial residual (resid0) = 1.157552615e+10 MLMG: Final Iter. 7 resid, resid/bnorm = 0.002752363682, 2.37774391e-13 MLMG: Timers: Solve = 0.675540134 Iter = 0.654227141 Bottom = 0.007774297 Done calling nodal solver Timestep 0 ends with TIME = 0.0004741795139 DT = 0.0004741795139 Timing summary: Advection :2.136686417 seconds MAC Proj :0.69886097 seconds Nodal Proj :0.881789194 seconds Reactions :4.810022488 seconds Misc :0.78667719 seconds Base State :0.004894945 seconds Time to advance time step: 9.330350066 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 186468750, 224718750 Time to write plotfile: 2.999727635 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 0.0004741795139 Cell Count: Level 0, 1327104 cells inner sponge: r_sp , r_tp : 186468750, 224718750 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1308380.202 MLMG: Initial residual (resid0) = 1308380.202 MLMG: Final Iter. 8 resid, resid/bnorm = 0.0001225722517, 9.368244148e-11 MLMG: Timers: Solve = 0.347972296 Iter = 0.332864984 Bottom = 0.008616748 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1308380.236 MLMG: Initial residual (resid0) = 0.9822511362 MLMG: Final Iter. 4 resid, resid/bnorm = 3.561760968e-05, 2.72226748e-11 MLMG: Timers: Solve = 0.188530292 Iter = 0.173014811 Bottom = 0.005230446 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5488883.985 MLMG: Initial residual (resid0) = 5488883.985 MLMG: Final Iter. 7 resid, resid/bnorm = 1.273612725e-06, 2.320349142e-13 MLMG: Timers: Solve = 0.680439785 Iter = 0.659774022 Bottom = 0.008063547 Done calling nodal solver Timestep 1 ends with TIME = 0.0004741795139 DT = 0.0004741795139 Timing summary: Advection :2.273346373 seconds MAC Proj :0.627099732 seconds Nodal Proj :0.890229047 seconds Reactions :4.898500185 seconds Misc :0.772283554 seconds Base State :0.004860475 seconds Time to advance time step: 9.468877154 Call to estdt for level 0 gives dt_lev = 0.2012294718 Minimum estdt over all levels = 0.2012294718 Call to estdt at beginning of step 2 gives dt =0.2012294718 dt_growth factor limits the new dt = 0.0005215974653  Timestep 2 starts with TIME = 0.0004741795139 DT = 0.0005215974653 Cell Count: Level 0, 1327104 cells inner sponge: r_sp , r_tp : 186468750, 224718750 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1426181.405 MLMG: Initial residual (resid0) = 1426181.405 MLMG: Final Iter. 8 resid, resid/bnorm = 0.0001354867418, 9.499965521e-11 MLMG: Timers: Solve = 0.346755906 Iter = 0.331897497 Bottom = 0.007842323 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1426184.06 MLMG: Initial residual (resid0) = 5132.459651 MLMG: Final Iter. 6 resid, resid/bnorm = 3.079236194e-05, 2.159073488e-11 MLMG: Timers: Solve = 0.268236277 Iter = 0.25275837 Bottom = 0.006399959 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6063789.798 MLMG: Initial residual (resid0) = 6063789.798 MLMG: Final Iter. 7 resid, resid/bnorm = 1.418645127e-06, 2.339535462e-13 MLMG: Timers: Solve = 0.675506302 Iter = 0.655032745 Bottom = 0.007269263 Done calling nodal solver Timestep 2 ends with TIME = 0.0009957769792 DT = 0.0005215974653 Timing summary: Advection :2.213952324 seconds MAC Proj :0.704690281 seconds Nodal Proj :0.885523366 seconds Reactions :4.76199542 seconds Misc :0.784910817 seconds Base State :0.005154613 seconds Time to advance time step: 9.351326086 Call to estdt for level 0 gives dt_lev = 0.20128497 Minimum estdt over all levels = 0.20128497 Call to estdt at beginning of step 3 gives dt =0.20128497 dt_growth factor limits the new dt = 0.0005737572118  Timestep 3 starts with TIME = 0.0009957769792 DT = 0.0005737572118 Cell Count: Level 0, 1327104 cells inner sponge: r_sp , r_tp : 186468750, 224718750 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1597942.993 MLMG: Initial residual (resid0) = 1597942.993 MLMG: Final Iter. 8 resid, resid/bnorm = 0.000151760134, 9.497218277e-11 MLMG: Timers: Solve = 0.346679365 Iter = 0.331580639 Bottom = 0.007815381 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1597945.914 MLMG: Initial residual (resid0) = 5863.170846 MLMG: Final Iter. 6 resid, resid/bnorm = 3.355391459e-05, 2.099815413e-11 MLMG: Timers: Solve = 0.265836746 Iter = 0.250697614 Bottom = 0.006791998 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6670310.291 MLMG: Initial residual (resid0) = 6670310.291 MLMG: Final Iter. 7 resid, resid/bnorm = 4.503816311e-06, 6.752034185e-13 MLMG: Timers: Solve = 0.676276069 Iter = 0.655548773 Bottom = 0.008327297 Done calling nodal solver Timestep 3 ends with TIME = 0.001569534191 DT = 0.0005737572118 Timing summary: Advection :2.142266954 seconds MAC Proj :0.704179537 seconds Nodal Proj :0.882388123 seconds Reactions :4.725103997 seconds Misc :0.783696576 seconds Base State :0.004928435 seconds Time to advance time step: 9.237894808 Writing plotfile 3 inner sponge: r_sp , r_tp : 186468750, 224718750 Time to write plotfile: 3.039756992 Total Time: 56.82424464 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [reacting_bubble_3d_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] [TOP]::amr.plot_file(nvals = 1) :: [reacting_bubble_3d_plt] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] AMReX (26.05-56-gb8117c772be8) finalized