Initializing AMReX (26.06-11-g9ed35ab0e584)... MPI initialized with 4 MPI processes MPI initialized with thread support level 0 AMReX (26.06-11-g9ed35ab0e584) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = cutoff densities: low density cutoff (for mapping the model) = 1e-10 buoyancy cutoff density (for zeroing rho - rho_0, centrifugal term) = 5e-10 anelastic cutoff = 1e-10 Maximum HSE Error = 4.547473509e-13 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile rt_2d_pltInitData after InitData Time to write plotfile: 0.02983985 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.001274492 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile rt_2d_pltafter_InitProj after InitProj Time to write plotfile: 0.027726616 Call to firstdt for level 0 gives dt_lev = 0.0006089835859 Multiplying dt_lev by init_shrink; dt_lev = 6.089835859e-05 Minimum firstdt over all levels = 6.089835859e-05 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.001291818 Iter = 0 Bottom = 0 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.08660444773 Minimum estdt over all levels = 0.08660444773 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.08660444773 Multiplying dt by init_shrink; dt = 0.008660444773 Ignoring this new dt since it's larger than the previous dt = 6.089835859e-05 Writing plotfile rt_2d_pltafter_DivuIter after final DivuIter Time to write plotfile: 0.027538481 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 0.002421164472 MLMG: Initial residual (resid0) = 0.002421164472 MLMG: Final Iter. 9 resid, resid/bnorm = 1.751907767e-13, 7.235806522e-11 MLMG: Timers: Solve = 0.019649193 Iter = 0.018558239 Bottom = 0.000271369 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 0.002421205691 MLMG: Initial residual (resid0) = 2.151449931e-06 MLMG: Final Iter. 7 resid, resid/bnorm = 9.927909435e-14, 4.100399017e-11 MLMG: Timers: Solve = 0.015494633 Iter = 0.014403087 Bottom = 0.000222427 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 58.12657035 MLMG: Initial residual (resid0) = 58.12657035 MLMG: Final Iter. 8 resid, resid/bnorm = 2.15578666e-11, 3.708780077e-13 MLMG: Timers: Solve = 0.054694927 Iter = 0.053598581 Bottom = 0.000196526 Done calling nodal solver Timestep 0 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.06132504 seconds MAC Proj :0.039799285 seconds Nodal Proj :0.060982059 seconds Reactions :0.004407052 seconds Misc :0.010791856 seconds Base State :0.000483623 seconds Time to advance time step: 0.180714583 Writing plotfile 0 after all initialization Time to write plotfile: 0.027106463 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 6.089835859e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.394238647e-05 MLMG: Initial residual (resid0) = 2.394238647e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 3.181792236e-16, 1.328936963e-11 MLMG: Timers: Solve = 0.019643888 Iter = 0.018551557 Bottom = 0.000282353 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.394218844e-05 MLMG: Initial residual (resid0) = 1.928423574e-06 MLMG: Final Iter. 9 resid, resid/bnorm = 6.036511589e-16, 2.521286475e-11 MLMG: Timers: Solve = 0.019443498 Iter = 0.018345402 Bottom = 0.000253744 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003539812449 MLMG: Initial residual (resid0) = 0.003539812449 MLMG: Final Iter. 8 resid, resid/bnorm = 1.329231863e-15, 3.755091216e-13 MLMG: Timers: Solve = 0.054700005 Iter = 0.053623497 Bottom = 0.000193948 Done calling nodal solver Timestep 1 ends with TIME = 6.089835859e-05 DT = 6.089835859e-05 Timing summary: Advection :0.060366414 seconds MAC Proj :0.043677525 seconds Nodal Proj :0.061333348 seconds Reactions :0.00434536 seconds Misc :0.009586016 seconds Base State :0.00053472 seconds Time to advance time step: 0.183611155 Call to estdt for level 0 gives dt_lev = 0.3128878797 Minimum estdt over all levels = 0.3128878797 Call to estdt at beginning of step 2 gives dt =0.3128878797 dt_growth factor limits the new dt = 6.698819445e-05  Timestep 2 starts with TIME = 6.089835859e-05 DT = 6.698819445e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.050043585e-05 MLMG: Initial residual (resid0) = 3.050043585e-05 MLMG: Final Iter. 9 resid, resid/bnorm = 2.284814624e-15, 7.491088439e-11 MLMG: Timers: Solve = 0.019437216 Iter = 0.018350566 Bottom = 0.000271565 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.059063412e-05 MLMG: Initial residual (resid0) = 5.66083759e-06 MLMG: Final Iter. 10 resid, resid/bnorm = 4.892627475e-16, 1.599387399e-11 MLMG: Timers: Solve = 0.021545575 Iter = 0.020451722 Bottom = 0.000280604 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.003894013591 MLMG: Initial residual (resid0) = 0.003894013591 MLMG: Final Iter. 8 resid, resid/bnorm = 1.490994828e-15, 3.828940996e-13 MLMG: Timers: Solve = 0.054814358 Iter = 0.053716055 Bottom = 0.000195386 Done calling nodal solver Timestep 2 ends with TIME = 0.000127886553 DT = 6.698819445e-05 Timing summary: Advection :0.060590302 seconds MAC Proj :0.045472941 seconds Nodal Proj :0.061640649 seconds Reactions :0.00420715 seconds Misc :0.009835791 seconds Base State :0.00047933 seconds Time to advance time step: 0.181929596 Call to estdt for level 0 gives dt_lev = 0.3130286362 Minimum estdt over all levels = 0.3130286362 Call to estdt at beginning of step 3 gives dt =0.3130286362 dt_growth factor limits the new dt = 7.36870139e-05  Timestep 3 starts with TIME = 0.000127886553 DT = 7.36870139e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.168800511e-05 MLMG: Initial residual (resid0) = 3.168800511e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 5.650700787e-16, 1.783230205e-11 MLMG: Timers: Solve = 0.021529003 Iter = 0.020420098 Bottom = 0.000283081 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.178722337e-05 MLMG: Initial residual (resid0) = 1.012935749e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 6.833616179e-16, 2.149799653e-11 MLMG: Timers: Solve = 0.021573944 Iter = 0.020423661 Bottom = 0.00027648 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004283414244 MLMG: Initial residual (resid0) = 0.004283414244 MLMG: Final Iter. 8 resid, resid/bnorm = 1.614810716e-15, 3.769914894e-13 MLMG: Timers: Solve = 0.054796762 Iter = 0.053717706 Bottom = 0.000190831 Done calling nodal solver Timestep 3 ends with TIME = 0.0002015735669 DT = 7.36870139e-05 Timing summary: Advection :0.060943978 seconds MAC Proj :0.047905514 seconds Nodal Proj :0.061273611 seconds Reactions :0.004237193 seconds Misc :0.009790364 seconds Base State :0.000466298 seconds Time to advance time step: 0.184355341 Call to estdt for level 0 gives dt_lev = 0.3130285358 Minimum estdt over all levels = 0.3130285358 Call to estdt at beginning of step 4 gives dt =0.3130285358 dt_growth factor limits the new dt = 8.105571529e-05  Timestep 4 starts with TIME = 0.0002015735669 DT = 8.105571529e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.570538736e-05 MLMG: Initial residual (resid0) = 3.570538736e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 7.571110825e-16, 2.120439347e-11 MLMG: Timers: Solve = 0.021432031 Iter = 0.020321632 Bottom = 0.000298398 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.581452755e-05 MLMG: Initial residual (resid0) = 1.504387741e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 8.870129024e-16, 2.476684639e-11 MLMG: Timers: Solve = 0.021737562 Iter = 0.020653204 Bottom = 0.000276037 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.004711755906 MLMG: Initial residual (resid0) = 0.004711755906 MLMG: Final Iter. 8 resid, resid/bnorm = 1.768550584e-15, 3.753485153e-13 MLMG: Timers: Solve = 0.054574481 Iter = 0.053489823 Bottom = 0.000192617 Done calling nodal solver Timestep 4 ends with TIME = 0.0002826292822 DT = 8.105571529e-05 Timing summary: Advection :0.06068745 seconds MAC Proj :0.047680066 seconds Nodal Proj :0.061291792 seconds Reactions :0.004249527 seconds Misc :0.009999549 seconds Base State :0.000600371 seconds Time to advance time step: 0.184112836 Call to estdt for level 0 gives dt_lev = 0.313028505 Minimum estdt over all levels = 0.313028505 Call to estdt at beginning of step 5 gives dt =0.313028505 dt_growth factor limits the new dt = 8.916128682e-05  Timestep 5 starts with TIME = 0.0002826292822 DT = 8.916128682e-05 Cell Count: Level 0, 131072 cells <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.013180326e-05 MLMG: Initial residual (resid0) = 4.013180326e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 9.681425651e-16, 2.412407334e-11 MLMG: Timers: Solve = 0.021849271 Iter = 0.020759946 Bottom = 0.000285432 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.025185748e-05 MLMG: Initial residual (resid0) = 2.044985444e-05 MLMG: Final Iter. 10 resid, resid/bnorm = 1.111036176e-15, 2.760210946e-11 MLMG: Timers: Solve = 0.02148384 Iter = 0.020410906 Bottom = 0.000274559 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 0.005182931901 MLMG: Initial residual (resid0) = 0.005182931901 MLMG: Final Iter. 8 resid, resid/bnorm = 1.942022931e-15, 3.746958224e-13 MLMG: Timers: Solve = 0.0542853 Iter = 0.053209325 Bottom = 0.00019411 Done calling nodal solver Timestep 5 ends with TIME = 0.000371790569 DT = 8.916128682e-05 Timing summary: Advection :0.060674992 seconds MAC Proj :0.047922831 seconds Nodal Proj :0.060714799 seconds Reactions :0.004214792 seconds Misc :0.009786187 seconds Base State :0.000468982 seconds Time to advance time step: 0.183524448 Writing plotfile 5 Time to write plotfile: 0.028561711 Total Time: 1.275625879 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [rt_2d_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] [TOP]::amr.plot_file(nvals = 1) :: [rt_2d_plt] [TOP]::amr.ref_ratio(nvals = 4) :: [2, 2, 2, 2] AMReX (26.06-11-g9ed35ab0e584) finalized