Initializing AMReX (26.09-122-ga846c6a9c672)... MPI initialized with 4 MPI processes MPI initialized with thread support level 0 AMReX (26.09-122-ga846c6a9c672) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = model.hse model file = model.hse reading initial model 512 points found in the initial model 6 variables found in the initial model model file mapping, level: 0 dr of MAESTRO base state = 781250.000000 dr of input file data = 781250.000000 maximum radius (cell-centered) of input model = 399609375.000000 setting r_cutoff to 330 radius at r_cutoff 258203125 Maximum HSE Error = 0.001041 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile test_convect_2d_pltInitData after InitData inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.249732922 inner sponge: r_sp , r_tp : 219921875, 296484375 Doing initial projection Calling nodal solver MLMG: Initial rhs = 6.126516885e+10 MLMG: Initial residual (resid0) = 6.126516885e+10 MLMG: Final Iter. 7 resid, resid/bnorm = 0.002288818359, 3.735921083e-14 MLMG: Timers: Solve = 0.06439147 Iter = 0.06207722 Bottom = 0.000347082 Done calling nodal solver Writing plotfile test_convect_2d_pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.249215325 Call to firstdt for level 0 gives dt_lev = 0.3657871977 Multiplying dt_lev by init_shrink; dt_lev = 0.03657871977 Minimum firstdt over all levels = 0.03657871977 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 3859584340 MLMG: Initial residual (resid0) = 3859584340 MLMG: Final Iter. 6 resid, resid/bnorm = 0.0004867911339, 1.261252744e-13 MLMG: Timers: Solve = 0.052122637 Iter = 0.050578358 Bottom = 0.000290945 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 0.3547800905 Minimum estdt over all levels = 0.3547800905 Call to estdt at end of istep_divu_iter = 1 gives dt = 0.3547800905 Multiplying dt by init_shrink; dt = 0.03547800905 Writing plotfile test_convect_2d_pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.251876854 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 0.03547800905 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.059199332e+10 MLMG: Initial residual (resid0) = 1.059199332e+10 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1071900353, 1.011991153e-11 MLMG: Timers: Solve = 0.02296085 Iter = 0.021272983 Bottom = 0.0004238 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.059199332e+10 MLMG: Initial residual (resid0) = 123656.1826 MLMG: Final Iter. 5 resid, resid/bnorm = 0.2197556028, 2.074733209e-11 MLMG: Timers: Solve = 0.016874772 Iter = 0.015270663 Bottom = 0.000276124 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.424216593e+10 MLMG: Initial residual (resid0) = 2.424216593e+10 MLMG: Final Iter. 6 resid, resid/bnorm = 0.1175193787, 4.847726025e-12 MLMG: Timers: Solve = 0.052063161 Iter = 0.050515278 Bottom = 0.000310515 Done calling nodal solver Timestep 0 ends with TIME = 0.03547800905 DT = 0.03547800905 Timing summary: Advection :0.117962873 seconds MAC Proj :0.04646746 seconds Nodal Proj :0.067174997 seconds Reactions :0.374602927 seconds Misc :0.09324981 seconds Base State :0.000617785 seconds Time to advance time step: 0.705580569 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.246841068 Writing checkpoint 0 after all initialization Writing checkpoint test_convect_2d_chk0000000 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 0.03547800905 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.056987975e+10 MLMG: Initial residual (resid0) = 1.056987975e+10 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1211298667, 1.145990963e-11 MLMG: Timers: Solve = 0.022887188 Iter = 0.021298277 Bottom = 0.000416644 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.056987974e+10 MLMG: Initial residual (resid0) = 1471.876408 MLMG: Final Iter. 4 resid, resid/bnorm = 0.240102473, 2.27157242e-11 MLMG: Timers: Solve = 0.014168131 Iter = 0.01256081 Bottom = 0.000203875 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1599045671 MLMG: Initial residual (resid0) = 1599045671 MLMG: Final Iter. 5 resid, resid/bnorm = 0.1505362988, 9.414133785e-11 MLMG: Timers: Solve = 0.043987296 Iter = 0.042405554 Bottom = 0.000263509 Done calling nodal solver Timestep 1 ends with TIME = 0.03547800905 DT = 0.03547800905 Timing summary: Advection :0.115083187 seconds MAC Proj :0.043784713 seconds Nodal Proj :0.058911792 seconds Reactions :0.372357859 seconds Misc :0.092778721 seconds Base State :0.000593533 seconds Time to advance time step: 0.689020472 Call to estdt for level 0 gives dt_lev = 0.3529259688 Minimum estdt over all levels = 0.3529259688 Call to estdt at beginning of step 2 gives dt =0.3529259688 dt_growth factor limits the new dt = 0.03902580996  Timestep 2 starts with TIME = 0.03547800905 DT = 0.03902580996 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9753119659 MLMG: Initial residual (resid0) = 9753119659 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1276168823, 1.308472435e-11 MLMG: Timers: Solve = 0.023293941 Iter = 0.021706699 Bottom = 0.000373955 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9753119657 MLMG: Initial residual (resid0) = 15754.04191 MLMG: Final Iter. 4 resid, resid/bnorm = 0.5134958738, 5.264939751e-11 MLMG: Timers: Solve = 0.01402224 Iter = 0.012425701 Bottom = 0.000207325 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1020734907 MLMG: Initial residual (resid0) = 1020734907 MLMG: Final Iter. 6 resid, resid/bnorm = 0.008885860443, 8.705355705e-12 MLMG: Timers: Solve = 0.052310077 Iter = 0.050725842 Bottom = 0.000313139 Done calling nodal solver Timestep 2 ends with TIME = 0.07450381901 DT = 0.03902580996 Timing summary: Advection :0.116780423 seconds MAC Proj :0.043830028 seconds Nodal Proj :0.067364726 seconds Reactions :0.372416011 seconds Misc :0.096402761 seconds Base State :0.00068396 seconds Time to advance time step: 0.697040488 Call to estdt for level 0 gives dt_lev = 0.3522809739 Minimum estdt over all levels = 0.3522809739 Call to estdt at beginning of step 3 gives dt =0.3522809739 dt_growth factor limits the new dt = 0.04292839095  Timestep 3 starts with TIME = 0.07450381901 DT = 0.04292839095 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9075727538 MLMG: Initial residual (resid0) = 9075727538 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1086936891, 1.197630588e-11 MLMG: Timers: Solve = 0.02313679 Iter = 0.021529219 Bottom = 0.000400493 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9075727536 MLMG: Initial residual (resid0) = 15175.54771 MLMG: Final Iter. 4 resid, resid/bnorm = 0.7519860929, 8.285683874e-11 MLMG: Timers: Solve = 0.013850371 Iter = 0.012119869 Bottom = 0.000203569 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1103382036 MLMG: Initial residual (resid0) = 1103382036 MLMG: Final Iter. 6 resid, resid/bnorm = 0.009425163269, 8.542066996e-12 MLMG: Timers: Solve = 0.052412477 Iter = 0.050849022 Bottom = 0.000325549 Done calling nodal solver Timestep 3 ends with TIME = 0.11743221 DT = 0.04292839095 Timing summary: Advection :0.118359248 seconds MAC Proj :0.043461951 seconds Nodal Proj :0.0675305 seconds Reactions :0.372676688 seconds Misc :0.099458753 seconds Base State :0.000599067 seconds Time to advance time step: 0.701748788 Call to estdt for level 0 gives dt_lev = 0.3519815355 Minimum estdt over all levels = 0.3519815355 Call to estdt at beginning of step 4 gives dt =0.3519815355 dt_growth factor limits the new dt = 0.04722123005  Timestep 4 starts with TIME = 0.11743221 DT = 0.04722123005 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8248850610 MLMG: Initial residual (resid0) = 8248850610 MLMG: Final Iter. 7 resid, resid/bnorm = 0.1091785431, 1.323560678e-11 MLMG: Timers: Solve = 0.022589276 Iter = 0.020979757 Bottom = 0.000410825 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8248850607 MLMG: Initial residual (resid0) = 14473.20863 MLMG: Final Iter. 4 resid, resid/bnorm = 0.3785336591, 4.588926108e-11 MLMG: Timers: Solve = 0.013985416 Iter = 0.01239495 Bottom = 0.000230232 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1153464230 MLMG: Initial residual (resid0) = 1153464230 MLMG: Final Iter. 6 resid, resid/bnorm = 0.01027870178, 8.911157808e-12 MLMG: Timers: Solve = 0.052425724 Iter = 0.050867648 Bottom = 0.000320368 Done calling nodal solver Timestep 4 ends with TIME = 0.16465344 DT = 0.04722123005 Timing summary: Advection :0.119051245 seconds MAC Proj :0.043110246 seconds Nodal Proj :0.067768517 seconds Reactions :0.37313494 seconds Misc :0.100271428 seconds Base State :0.000647862 seconds Time to advance time step: 0.703597023 Call to estdt for level 0 gives dt_lev = 0.3519075579 Minimum estdt over all levels = 0.3519075579 Call to estdt at beginning of step 5 gives dt =0.3519075579 dt_growth factor limits the new dt = 0.05194335306  Timestep 5 starts with TIME = 0.16465344 DT = 0.05194335306 Cell Count: Level 0, 163840 cells inner sponge: r_sp , r_tp : 219921875, 296484375 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6944513254 MLMG: Initial residual (resid0) = 6944513254 MLMG: Final Iter. 7 resid, resid/bnorm = 0.08908589184, 1.282824132e-11 MLMG: Timers: Solve = 0.022932572 Iter = 0.021350591 Bottom = 0.000429812 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6944513252 MLMG: Initial residual (resid0) = 13528.23695 MLMG: Final Iter. 4 resid, resid/bnorm = 0.3968143468, 5.714069978e-11 MLMG: Timers: Solve = 0.013770427 Iter = 0.012127894 Bottom = 0.000207973 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1162694978 MLMG: Initial residual (resid0) = 1162694978 MLMG: Final Iter. 6 resid, resid/bnorm = 0.01120948792, 9.640953239e-12 MLMG: Timers: Solve = 0.052353217 Iter = 0.050764938 Bottom = 0.000322558 Done calling nodal solver Timestep 5 ends with TIME = 0.2165967931 DT = 0.05194335306 Timing summary: Advection :0.120717166 seconds MAC Proj :0.043362804 seconds Nodal Proj :0.067391768 seconds Reactions :0.373852584 seconds Misc :0.100143334 seconds Base State :0.00059709 seconds Time to advance time step: 0.705732024 Writing plotfile 5 inner sponge: r_sp , r_tp : 219921875, 296484375 Time to write plotfile: 0.29831005 Writing checkpoint 5 Writing checkpoint test_convect_2d_chk0000005 Total Time: 6.777647771 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [test_convect_2d_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] [TOP]::amr.plot_file(nvals = 1) :: [test_convect_2d_plt] AMReX (26.09-122-ga846c6a9c672) finalized