Initializing AMReX (26.10-92-gec6902bd5e2b)... MPI initialized with 4 MPI processes MPI initialized with thread support level 0 AMReX (26.10-92-gec6902bd5e2b) initialized Calling Setup() Calling ReadParameters() reading extern runtime parameters ... Calling VariableSetup() Calling BCSetup() Calling BaseStateGeometry::Init() Calling Init() Calling InitData() initdata model_File = 5peaks_const_grav.dat model file = 5peaks_const_grav.dat reading initial model 1000 points found in the initial model 10 variables found in the initial model WARNING: variable not found: gravity WARNING: variable not found: abar WARNING: variable not found: zbar WARNING: variable not found: gpot WARNING: variable not found: cno model file mapping, level: 0 dr of MAESTRO base state = 93750000.000000 dr of input file data = 10010010.010010 maximum radius (cell-centered) of input model = 10000000000.000000 WARNING: resolution of base state array is not an integer multiple of the initial model's resolution. make sure this is a desired property as this could lead to aliasing when performing the interpolation. modulus = 3659909.909910 setting r_cutoff to 105 radius at r_cutoff 9890625000 Maximum HSE Error = 0.054171 (after putting initial model into base state arrays, and for density < base_cutoff_density) Writing plotfile pltInitData after InitData inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.025655208 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Doing initial projection Calling nodal solver MLMG: Initial rhs = 0 MLMG: Initial residual (resid0) = 0 MLMG: No iterations needed MLMG: Timers: Solve = 0.000291587 Iter = 0 Bottom = 0 Done calling nodal solver Writing plotfile pltafter_InitProj after InitProj inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.024341565 Call to firstdt for level 0 gives dt_lev = 0.01907406555 Multiplying dt_lev by init_shrink; dt_lev = 0.001907406555 Minimum firstdt over all levels = 0.001907406555 Doing initial divu iteration #1 Calling nodal solver MLMG: Initial rhs = 4.945354899e-27 MLMG: Initial residual (resid0) = 4.945354899e-27 MLMG: Final Iter. 3 resid, resid/bnorm = 2.357566962e-30, 0.0004767235133 MLMG: Timers: Solve = 0.00349312 Iter = 0.003241202 Bottom = 5.8554e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 1 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #2 Calling nodal solver MLMG: Initial rhs = 2.306075226e-30 MLMG: Initial residual (resid0) = 2.306075226e-30 MLMG: Final Iter. 5 resid, resid/bnorm = 1.933658701e-37, 8.385063417e-08 MLMG: Timers: Solve = 0.005466412 Iter = 0.005220848 Bottom = 8.4344e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 2 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Doing initial divu iteration #3 Calling nodal solver MLMG: Initial rhs = 9.742172192e-32 MLMG: Initial residual (resid0) = 9.742172192e-32 MLMG: Final Iter. 4 resid, resid/bnorm = 7.42570061e-41, 7.622222708e-10 MLMG: Timers: Solve = 0.004441749 Iter = 0.004193297 Bottom = 6.8905e-05 Done calling nodal solver Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at end of istep_divu_iter = 3 gives dt = 1e+20 Multiplying dt by init_shrink; dt = 1e+19 Ignoring this new dt since it's larger than the previous dt = 0.001907406555 Writing plotfile pltafter_DivuIter after final DivuIter inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.023978514 Doing initial pressure iteration #1  Timestep 0 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.539879803e-20 MLMG: Initial residual (resid0) = 7.539879803e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 1.368599673e-30, 1.815147865e-11 MLMG: Timers: Solve = 0.004778211 Iter = 0.004539339 Bottom = 0.000147855 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.539879811e-20 MLMG: Initial residual (resid0) = 2.477513817e-27 MLMG: Final Iter. 4 resid, resid/bnorm = 4.81361945e-30, 6.384212442e-11 MLMG: Timers: Solve = 0.00211335 Iter = 0.001887267 Bottom = 6.1346e-05 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.165359286e-17 MLMG: Initial residual (resid0) = 9.165359286e-17 MLMG: Final Iter. 9 resid, resid/bnorm = 8.873551196e-27, 9.681618493e-11 MLMG: Timers: Solve = 0.009874929 Iter = 0.009625878 Bottom = 0.000143027 Done calling nodal solver Timestep 0 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.011219109 seconds MAC Proj :0.008033673 seconds Nodal Proj :0.011465442 seconds Reactions :0.033871863 seconds Misc :0.003540464 seconds Base State :3.299999984e-08 seconds Time to advance time step: 0.07005584 Writing plotfile 0 after all initialization inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.025034018 Writing checkpoint 0 after all initialization Writing checkpoint chk0000000 Beginning main evolution  Timestep 1 starts with TIME = 0 DT = 0.001907406555 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.258690572e-26 MLMG: Initial residual (resid0) = 1.258690572e-26 MLMG: Final Iter. 10 resid, resid/bnorm = 1.078808793e-37, 8.570881646e-12 MLMG: Timers: Solve = 0.004768094 Iter = 0.004542906 Bottom = 0.000145802 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.258690572e-26 MLMG: Initial residual (resid0) = 1.078794443e-37 MLMG: No iterations needed MLMG: Timers: Solve = 0.000231887 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.748206638e-19 MLMG: Initial residual (resid0) = 1.748206638e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.692540939e-29, 9.681583985e-11 MLMG: Timers: Solve = 0.009870484 Iter = 0.009611953 Bottom = 0.000144115 Done calling nodal solver Timestep 1 ends with TIME = 0.001907406555 DT = 0.001907406555 Timing summary: Advection :0.011517345 seconds MAC Proj :0.006050113 seconds Nodal Proj :0.011415004 seconds Reactions :0.03340687 seconds Misc :0.00364113 seconds Base State :3.600000009e-08 seconds Time to advance time step: 0.06854686 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 2 gives dt =1e+20 dt_growth factor limits the new dt = 0.002002776883  Timestep 2 starts with TIME = 0.001907406555 DT = 0.002002776883 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.079682858e-27 MLMG: Initial residual (resid0) = 8.079682858e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 1.198180588e-37, 1.482954974e-11 MLMG: Timers: Solve = 0.005076774 Iter = 0.004698063 Bottom = 0.000145248 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.465415674e-27 MLMG: Initial residual (resid0) = 2.601349809e-27 MLMG: Final Iter. 10 resid, resid/bnorm = 8.686741106e-37, 9.177347731e-11 MLMG: Timers: Solve = 0.004742145 Iter = 0.004514438 Bottom = 0.000143327 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.835900478e-19 MLMG: Initial residual (resid0) = 1.835900478e-19 MLMG: Final Iter. 10 resid, resid/bnorm = 3.016126664e-30, 1.642859567e-11 MLMG: Timers: Solve = 0.010895551 Iter = 0.010636225 Bottom = 0.000157735 Done calling nodal solver Timestep 2 ends with TIME = 0.003910183437 DT = 0.002002776883 Timing summary: Advection :0.010560294 seconds MAC Proj :0.010887088 seconds Nodal Proj :0.012457087 seconds Reactions :0.033300791 seconds Misc :0.003473846 seconds Base State :1.05e-07 seconds Time to advance time step: 0.070810588 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 3 gives dt =1e+20 dt_growth factor limits the new dt = 0.002102915727  Timestep 3 starts with TIME = 0.003910183437 DT = 0.002102915727 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.320997545e-21 MLMG: Initial residual (resid0) = 8.320997545e-21 MLMG: Final Iter. 10 resid, resid/bnorm = 7.676937314e-31, 9.225981949e-11 MLMG: Timers: Solve = 0.004758697 Iter = 0.004529816 Bottom = 0.000141868 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.320997545e-21 MLMG: Initial residual (resid0) = 7.676937314e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.00023472 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.927397785e-19 MLMG: Initial residual (resid0) = 1.927397785e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.866031116e-29, 9.681608698e-11 MLMG: Timers: Solve = 0.009941686 Iter = 0.009679199 Bottom = 0.000142829 Done calling nodal solver Timestep 3 ends with TIME = 0.006013099164 DT = 0.002102915727 Timing summary: Advection :0.011060925 seconds MAC Proj :0.006055783 seconds Nodal Proj :0.011505476 seconds Reactions :0.033581066 seconds Misc :0.003475657 seconds Base State :6.19999998e-08 seconds Time to advance time step: 0.065817487 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 4 gives dt =1e+20 dt_growth factor limits the new dt = 0.002208061513  Timestep 4 starts with TIME = 0.006013099164 DT = 0.002208061513 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.754886737e-29 MLMG: Initial residual (resid0) = 4.754886737e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 3.764067041e-39, 7.916207577e-11 MLMG: Timers: Solve = 0.00474547 Iter = 0.004521115 Bottom = 0.000145155 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.754886737e-29 MLMG: Initial residual (resid0) = 3.764067041e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000228228 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.023767674e-19 MLMG: Initial residual (resid0) = 2.023767674e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.959340014e-29, 9.681644979e-11 MLMG: Timers: Solve = 0.009914663 Iter = 0.009657409 Bottom = 0.00014415 Done calling nodal solver Timestep 4 ends with TIME = 0.008221160677 DT = 0.002208061513 Timing summary: Advection :0.010602326 seconds MAC Proj :0.006033424 seconds Nodal Proj :0.011498186 seconds Reactions :0.033603838 seconds Misc :0.003465976 seconds Base State :6.399999997e-08 seconds Time to advance time step: 0.065343474 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 5 gives dt =1e+20 dt_growth factor limits the new dt = 0.002318464589  Timestep 5 starts with TIME = 0.008221160677 DT = 0.002318464589 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.322219309e-29 MLMG: Initial residual (resid0) = 3.322219309e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.771717916e-39, 8.342970941e-11 MLMG: Timers: Solve = 0.0047301 Iter = 0.004504142 Bottom = 0.000144048 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.322219309e-29 MLMG: Initial residual (resid0) = 2.771717916e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000228803 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.124956058e-19 MLMG: Initial residual (resid0) = 2.124956058e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.057307256e-29, 9.681646112e-11 MLMG: Timers: Solve = 0.009933312 Iter = 0.009682177 Bottom = 0.000142946 Done calling nodal solver Timestep 5 ends with TIME = 0.01053962527 DT = 0.002318464589 Timing summary: Advection :0.010647302 seconds MAC Proj :0.006043392 seconds Nodal Proj :0.011489081 seconds Reactions :0.033664784 seconds Misc :0.003453666 seconds Base State :9.999999984e-08 seconds Time to advance time step: 0.065438148 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 6 gives dt =1e+20 dt_growth factor limits the new dt = 0.002434387818  Timestep 6 starts with TIME = 0.01053962527 DT = 0.002434387818 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.48000074e-29 MLMG: Initial residual (resid0) = 3.48000074e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 2.910365188e-39, 8.363116578e-11 MLMG: Timers: Solve = 0.004738386 Iter = 0.004510534 Bottom = 0.000142588 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.48000074e-29 MLMG: Initial residual (resid0) = 2.910365188e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000236506 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.231203861e-19 MLMG: Initial residual (resid0) = 2.231203861e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.160173581e-29, 9.681650428e-11 MLMG: Timers: Solve = 0.009886964 Iter = 0.009636612 Bottom = 0.000145428 Done calling nodal solver Timestep 6 ends with TIME = 0.01297401308 DT = 0.002434387818 Timing summary: Advection :0.010822631 seconds MAC Proj :0.006030438 seconds Nodal Proj :0.01144239 seconds Reactions :0.033368903 seconds Misc :0.003446591 seconds Base State :5.799999991e-08 seconds Time to advance time step: 0.065245277 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 7 gives dt =1e+20 dt_growth factor limits the new dt = 0.002556107209  Timestep 7 starts with TIME = 0.01297401308 DT = 0.002556107209 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.653536033e-29 MLMG: Initial residual (resid0) = 3.653536033e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 3.05578914e-39, 8.363922273e-11 MLMG: Timers: Solve = 0.004806346 Iter = 0.004575689 Bottom = 0.000150622 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.653536033e-29 MLMG: Initial residual (resid0) = 3.05578914e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000233648 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.342764054e-19 MLMG: Initial residual (resid0) = 2.342764054e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.268170103e-29, 9.681598535e-11 MLMG: Timers: Solve = 0.009890637 Iter = 0.009627185 Bottom = 0.000143756 Done calling nodal solver Timestep 7 ends with TIME = 0.01553012029 DT = 0.002556107209 Timing summary: Advection :0.011020574 seconds MAC Proj :0.006116912 seconds Nodal Proj :0.011440768 seconds Reactions :0.033348267 seconds Misc :0.003441818 seconds Base State :5.800000014e-08 seconds Time to advance time step: 0.065512798 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 8 gives dt =1e+20 dt_growth factor limits the new dt = 0.002683912569  Timestep 8 starts with TIME = 0.01553012029 DT = 0.002683912569 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.836209175e-29 MLMG: Initial residual (resid0) = 3.836209175e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 3.207799195e-39, 8.361898554e-11 MLMG: Timers: Solve = 0.00508724 Iter = 0.004735138 Bottom = 0.000148923 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.836209175e-29 MLMG: Initial residual (resid0) = 3.207799195e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022689 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.459902256e-19 MLMG: Initial residual (resid0) = 2.459902256e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.381592932e-29, 9.681656765e-11 MLMG: Timers: Solve = 0.009847951 Iter = 0.009592134 Bottom = 0.000141775 Done calling nodal solver Timestep 8 ends with TIME = 0.01821403286 DT = 0.002683912569 Timing summary: Advection :0.010658025 seconds MAC Proj :0.006365335 seconds Nodal Proj :0.011406835 seconds Reactions :0.03360522 seconds Misc :0.003442986 seconds Base State :6.699999999e-08 seconds Time to advance time step: 0.065619376 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 9 gives dt =1e+20 dt_growth factor limits the new dt = 0.002818108198  Timestep 9 starts with TIME = 0.01821403286 DT = 0.002818108198 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.027964028e-29 MLMG: Initial residual (resid0) = 4.027964028e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 3.368343158e-39, 8.362396323e-11 MLMG: Timers: Solve = 0.005101108 Iter = 0.004869753 Bottom = 0.000147941 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.027964028e-29 MLMG: Initial residual (resid0) = 3.368343158e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000226762 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.582897369e-19 MLMG: Initial residual (resid0) = 2.582897369e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.500665958e-29, 9.681631133e-11 MLMG: Timers: Solve = 0.009833891 Iter = 0.009581585 Bottom = 0.000144288 Done calling nodal solver Timestep 9 ends with TIME = 0.02103214106 DT = 0.002818108198 Timing summary: Advection :0.010678756 seconds MAC Proj :0.006399266 seconds Nodal Proj :0.011409043 seconds Reactions :0.033282751 seconds Misc :0.00344256 seconds Base State :6.200000002e-08 seconds Time to advance time step: 0.065355817 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 10 gives dt =1e+20 dt_growth factor limits the new dt = 0.002959013608  Timestep 10 starts with TIME = 0.02103214106 DT = 0.002959013608 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.22942923e-29 MLMG: Initial residual (resid0) = 4.22942923e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 3.537210833e-39, 8.363329047e-11 MLMG: Timers: Solve = 0.005162193 Iter = 0.004933904 Bottom = 0.000150186 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.22942923e-29 MLMG: Initial residual (resid0) = 3.537210833e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000229573 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.696786268e-19 MLMG: Initial residual (resid0) = 2.696786268e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 1.752735879e-29, 6.499350357e-11 MLMG: Timers: Solve = 0.009611984 Iter = 0.009356187 Bottom = 0.000146266 Done calling nodal solver Timestep 10 ends with TIME = 0.02399115467 DT = 0.002959013608 Timing summary: Advection :0.010694574 seconds MAC Proj :0.006449273 seconds Nodal Proj :0.011206129 seconds Reactions :0.033319571 seconds Misc :0.003491745 seconds Base State :5.100000022e-08 seconds Time to advance time step: 0.06530061 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 11 gives dt =1e+20 dt_growth factor limits the new dt = 0.003106964288  Timestep 11 starts with TIME = 0.02399115467 DT = 0.003106964288 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 1.271430598e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.30814865e-31, 4.961457322e-11 MLMG: Timers: Solve = 0.005148679 Iter = 0.004921916 Bottom = 0.000143511 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.271430598e-20 MLMG: Initial residual (resid0) = 6.30814865e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000231413 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.84764435e-19 MLMG: Initial residual (resid0) = 2.84764435e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.756956678e-29, 9.681534419e-11 MLMG: Timers: Solve = 0.009617722 Iter = 0.009355915 Bottom = 0.000150622 Done calling nodal solver Timestep 11 ends with TIME = 0.02709811896 DT = 0.003106964288 Timing summary: Advection :0.010715048 seconds MAC Proj :0.006447996 seconds Nodal Proj :0.011174918 seconds Reactions :0.033385948 seconds Misc :0.003501758 seconds Base State :6.100000016e-08 seconds Time to advance time step: 0.065377837 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 12 gives dt =1e+20 dt_growth factor limits the new dt = 0.003262312503  Timestep 12 starts with TIME = 0.02709811896 DT = 0.003262312503 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.610320828e-29 MLMG: Initial residual (resid0) = 5.610320828e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 4.569609069e-39, 8.145004909e-11 MLMG: Timers: Solve = 0.00513202 Iter = 0.00490616 Bottom = 0.000144008 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.610320828e-29 MLMG: Initial residual (resid0) = 4.569609069e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000229297 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 2.990026567e-19 MLMG: Initial residual (resid0) = 2.990026567e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.894826781e-29, 9.681608895e-11 MLMG: Timers: Solve = 0.009580291 Iter = 0.009323324 Bottom = 0.000143141 Done calling nodal solver Timestep 12 ends with TIME = 0.03036043146 DT = 0.003262312503 Timing summary: Advection :0.010806054 seconds MAC Proj :0.006464206 seconds Nodal Proj :0.01112519 seconds Reactions :0.033563616 seconds Misc :0.003449068 seconds Base State :6.300000011e-08 seconds Time to advance time step: 0.065551446 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 13 gives dt =1e+20 dt_growth factor limits the new dt = 0.003425428128  Timestep 13 starts with TIME = 0.03036043146 DT = 0.003425428128 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.901026128e-29 MLMG: Initial residual (resid0) = 4.901026128e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 4.094624941e-39, 8.354627856e-11 MLMG: Timers: Solve = 0.004976507 Iter = 0.004750849 Bottom = 0.000145444 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.901026128e-29 MLMG: Initial residual (resid0) = 4.094624941e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000228388 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.139527895e-19 MLMG: Initial residual (resid0) = 3.139527895e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.039570046e-29, 9.68161503e-11 MLMG: Timers: Solve = 0.009599479 Iter = 0.009343714 Bottom = 0.000146874 Done calling nodal solver Timestep 13 ends with TIME = 0.03378585959 DT = 0.003425428128 Timing summary: Advection :0.010933379 seconds MAC Proj :0.006391668 seconds Nodal Proj :0.011158753 seconds Reactions :0.033343598 seconds Misc :0.003437255 seconds Base State :5.9e-08 seconds Time to advance time step: 0.065398746 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 14 gives dt =1e+20 dt_growth factor limits the new dt = 0.003596699534  Timestep 14 starts with TIME = 0.03378585959 DT = 0.003596699534 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 5.14106632e-29 MLMG: Initial residual (resid0) = 5.14106632e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 4.299175281e-39, 8.362419415e-11 MLMG: Timers: Solve = 0.004753806 Iter = 0.004524939 Bottom = 0.00014579 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 5.14106632e-29 MLMG: Initial residual (resid0) = 4.299175281e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000227721 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.461558643e-19 MLMG: Initial residual (resid0) = 3.461558643e-19 MLMG: Final Iter. 10 resid, resid/bnorm = 4.48221676e-30, 1.29485507e-11 MLMG: Timers: Solve = 0.01062644 Iter = 0.010373439 Bottom = 0.000159253 Done calling nodal solver Timestep 14 ends with TIME = 0.03738255912 DT = 0.003596699534 Timing summary: Advection :0.01128925 seconds MAC Proj :0.006041833 seconds Nodal Proj :0.012306078 seconds Reactions :0.033356094 seconds Misc :0.003449807 seconds Base State :6.200000024e-08 seconds Time to advance time step: 0.066576281 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 15 gives dt =1e+20 dt_growth factor limits the new dt = 0.003776534511  Timestep 15 starts with TIME = 0.03738255912 DT = 0.003776534511 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 1.44706648e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 8.545017015e-31, 5.905061816e-11 MLMG: Timers: Solve = 0.004806426 Iter = 0.004581296 Bottom = 0.000143482 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.44706648e-20 MLMG: Initial residual (resid0) = 8.545017015e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000230495 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.441858592e-19 MLMG: Initial residual (resid0) = 3.441858592e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.235475035e-29, 6.494964785e-11 MLMG: Timers: Solve = 0.009587939 Iter = 0.009337805 Bottom = 0.000143625 Done calling nodal solver Timestep 15 ends with TIME = 0.04115909363 DT = 0.003776534511 Timing summary: Advection :0.011634556 seconds MAC Proj :0.006096122 seconds Nodal Proj :0.011141521 seconds Reactions :0.033291722 seconds Misc :0.003463349 seconds Base State :6.500000005e-08 seconds Time to advance time step: 0.065758415 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 16 gives dt =1e+20 dt_growth factor limits the new dt = 0.003965361236  Timestep 16 starts with TIME = 0.04115909363 DT = 0.003965361236 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 1.62270343e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 6.188320113e-31, 3.813586634e-11 MLMG: Timers: Solve = 0.004747249 Iter = 0.004519922 Bottom = 0.000143373 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.62270343e-20 MLMG: Initial residual (resid0) = 6.188320113e-31 MLMG: No iterations needed MLMG: Timers: Solve = 0.000236985 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.63439598e-19 MLMG: Initial residual (resid0) = 3.63439598e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.518688453e-29, 9.68163203e-11 MLMG: Timers: Solve = 0.009580248 Iter = 0.00932694 Bottom = 0.000142202 Done calling nodal solver Timestep 16 ends with TIME = 0.04512445487 DT = 0.003965361236 Timing summary: Advection :0.011219733 seconds MAC Proj :0.006187816 seconds Nodal Proj :0.011490006 seconds Reactions :0.033011771 seconds Misc :0.003444199 seconds Base State :6.100000016e-08 seconds Time to advance time step: 0.065500011 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 17 gives dt =1e+20 dt_growth factor limits the new dt = 0.004163629298  Timestep 17 starts with TIME = 0.04512445487 DT = 0.004163629298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.177089e-29 MLMG: Initial residual (resid0) = 7.177089e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 5.832624598e-39, 8.126727421e-11 MLMG: Timers: Solve = 0.004741061 Iter = 0.004514598 Bottom = 0.000147088 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.177089e-29 MLMG: Initial residual (resid0) = 5.832624598e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000230827 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 3.816115779e-19 MLMG: Initial residual (resid0) = 3.816115779e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.694626968e-29, 9.681642755e-11 MLMG: Timers: Solve = 0.009657789 Iter = 0.00935328 Bottom = 0.000148319 Done calling nodal solver Timestep 17 ends with TIME = 0.04928808417 DT = 0.004163629298 Timing summary: Advection :0.011558995 seconds MAC Proj :0.006158222 seconds Nodal Proj :0.011211569 seconds Reactions :0.032964995 seconds Misc :0.003508778 seconds Base State :1.139999997e-07 seconds Time to advance time step: 0.065540332 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 18 gives dt =1e+20 dt_growth factor limits the new dt = 0.004371810763  Timestep 18 starts with TIME = 0.04928808417 DT = 0.004371810763 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.255765533e-29 MLMG: Initial residual (resid0) = 6.255765533e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 5.225517644e-39, 8.353122596e-11 MLMG: Timers: Solve = 0.004739586 Iter = 0.004512918 Bottom = 0.000143726 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.255765533e-29 MLMG: Initial residual (resid0) = 5.225517644e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00024223 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.006921568e-19 MLMG: Initial residual (resid0) = 4.006921568e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 3.879352539e-29, 9.681628335e-11 MLMG: Timers: Solve = 0.009650196 Iter = 0.009385876 Bottom = 0.000143918 Done calling nodal solver Timestep 18 ends with TIME = 0.05365989493 DT = 0.004371810763 Timing summary: Advection :0.011090698 seconds MAC Proj :0.006040872 seconds Nodal Proj :0.011535631 seconds Reactions :0.033079576 seconds Misc :0.003692575 seconds Base State :3.300000007e-08 seconds Time to advance time step: 0.06558048 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 19 gives dt =1e+20 dt_growth factor limits the new dt = 0.004590401301  Timestep 19 starts with TIME = 0.05365989493 DT = 0.004590401301 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.561355155e-29 MLMG: Initial residual (resid0) = 6.561355155e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 5.487552049e-39, 8.363443098e-11 MLMG: Timers: Solve = 0.004747876 Iter = 0.004514359 Bottom = 0.000147035 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.561355155e-29 MLMG: Initial residual (resid0) = 5.487552049e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000228253 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.207267646e-19 MLMG: Initial residual (resid0) = 4.207267646e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.073303314e-29, 9.681588281e-11 MLMG: Timers: Solve = 0.009908739 Iter = 0.009657615 Bottom = 0.000144675 Done calling nodal solver Timestep 19 ends with TIME = 0.05825029623 DT = 0.004590401301 Timing summary: Advection :0.011016855 seconds MAC Proj :0.006038015 seconds Nodal Proj :0.011467691 seconds Reactions :0.033001696 seconds Misc :0.003825928 seconds Base State :5.400000003e-08 seconds Time to advance time step: 0.065483162 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 20 gives dt =1e+20 dt_growth factor limits the new dt = 0.004819921366  Timestep 20 starts with TIME = 0.05825029623 DT = 0.004819921366 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 6.889328973e-29 MLMG: Initial residual (resid0) = 6.889328973e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 5.760833275e-39, 8.361965726e-11 MLMG: Timers: Solve = 0.004749672 Iter = 0.004521827 Bottom = 0.000141988 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 6.889328973e-29 MLMG: Initial residual (resid0) = 5.760833275e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000236125 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.417631028e-19 MLMG: Initial residual (resid0) = 4.417631028e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.276989665e-29, 9.681636237e-11 MLMG: Timers: Solve = 0.009898144 Iter = 0.009646899 Bottom = 0.000144391 Done calling nodal solver Timestep 20 ends with TIME = 0.0630702176 DT = 0.004819921366 Timing summary: Advection :0.011032797 seconds MAC Proj :0.006038917 seconds Nodal Proj :0.011454915 seconds Reactions :0.033377653 seconds Misc :0.003446069 seconds Base State :6.500000005e-08 seconds Time to advance time step: 0.065492442 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 21 gives dt =1e+20 dt_growth factor limits the new dt = 0.005060917435  Timestep 21 starts with TIME = 0.0630702176 DT = 0.005060917435 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.233523435e-29 MLMG: Initial residual (resid0) = 7.233523435e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 6.049085974e-39, 8.36257189e-11 MLMG: Timers: Solve = 0.004756561 Iter = 0.004530326 Bottom = 0.000145284 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.233523435e-29 MLMG: Initial residual (resid0) = 6.049085974e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000226825 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.612419694e-19 MLMG: Initial residual (resid0) = 4.612419694e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 2.70927306e-29, 5.873864999e-11 MLMG: Timers: Solve = 0.009973307 Iter = 0.009687696 Bottom = 0.000144679 Done calling nodal solver Timestep 21 ends with TIME = 0.06813113503 DT = 0.005060917435 Timing summary: Advection :0.01069832 seconds MAC Proj :0.006033605 seconds Nodal Proj :0.011529969 seconds Reactions :0.033281441 seconds Misc :0.003773805 seconds Base State :1.190000001e-07 seconds Time to advance time step: 0.065454617 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 22 gives dt =1e+20 dt_growth factor limits the new dt = 0.005313963306  Timestep 22 starts with TIME = 0.06813113503 DT = 0.005313963306 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 2.174577793e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 1.127136258e-30, 5.183241832e-11 MLMG: Timers: Solve = 0.004745236 Iter = 0.004522895 Bottom = 0.00014757 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.174577793e-20 MLMG: Initial residual (resid0) = 1.127136258e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000229093 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 4.870438209e-19 MLMG: Initial residual (resid0) = 4.870438209e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.715379468e-29, 9.681632876e-11 MLMG: Timers: Solve = 0.009902395 Iter = 0.009648353 Bottom = 0.000143678 Done calling nodal solver Timestep 22 ends with TIME = 0.07344509834 DT = 0.005313963306 Timing summary: Advection :0.010720674 seconds MAC Proj :0.006029381 seconds Nodal Proj :0.01145447 seconds Reactions :0.033629323 seconds Misc :0.003446501 seconds Base State :5.9e-08 seconds Time to advance time step: 0.065425483 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 23 gives dt =1e+20 dt_growth factor limits the new dt = 0.005579661472  Timestep 23 starts with TIME = 0.07344509834 DT = 0.005579661472 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.907559692e-29 MLMG: Initial residual (resid0) = 9.907559692e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 8.035191129e-39, 8.110161714e-11 MLMG: Timers: Solve = 0.004734662 Iter = 0.004501072 Bottom = 0.000144631 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.907559692e-29 MLMG: Initial residual (resid0) = 8.035191129e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000230349 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.113960119e-19 MLMG: Initial residual (resid0) = 5.113960119e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 4.951137368e-29, 9.681611221e-11 MLMG: Timers: Solve = 0.009923118 Iter = 0.009665309 Bottom = 0.000146731 Done calling nodal solver Timestep 23 ends with TIME = 0.07902475981 DT = 0.005579661472 Timing summary: Advection :0.01069738 seconds MAC Proj :0.006026939 seconds Nodal Proj :0.011480886 seconds Reactions :0.033592252 seconds Misc :0.003441181 seconds Base State :6.099999972e-08 seconds Time to advance time step: 0.065392492 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 24 gives dt =1e+20 dt_growth factor limits the new dt = 0.005858644545  Timestep 24 starts with TIME = 0.07902475981 DT = 0.005858644545 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.38374944e-29 MLMG: Initial residual (resid0) = 8.38374944e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 7.00283213e-39, 8.352864288e-11 MLMG: Timers: Solve = 0.004745481 Iter = 0.004515299 Bottom = 0.00014448 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.38374944e-29 MLMG: Initial residual (resid0) = 7.00283213e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000232198 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.369658125e-19 MLMG: Initial residual (resid0) = 5.369658125e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.198681958e-29, 9.681588356e-11 MLMG: Timers: Solve = 0.009925568 Iter = 0.009674107 Bottom = 0.000151859 Done calling nodal solver Timestep 24 ends with TIME = 0.08488340435 DT = 0.005858644545 Timing summary: Advection :0.01072136 seconds MAC Proj :0.006036446 seconds Nodal Proj :0.011487586 seconds Reactions :0.033762003 seconds Misc :0.00345032 seconds Base State :6.100000016e-08 seconds Time to advance time step: 0.065601299 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 25 gives dt =1e+20 dt_growth factor limits the new dt = 0.006151576773  Timestep 25 starts with TIME = 0.08488340435 DT = 0.006151576773 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.792938961e-29 MLMG: Initial residual (resid0) = 8.792938961e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 7.353072668e-39, 8.362474368e-11 MLMG: Timers: Solve = 0.004749975 Iter = 0.004521871 Bottom = 0.000146553 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.792938961e-29 MLMG: Initial residual (resid0) = 7.353072668e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00023561 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.638141032e-19 MLMG: Initial residual (resid0) = 5.638141032e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.458639167e-29, 9.681629347e-11 MLMG: Timers: Solve = 0.009996214 Iter = 0.009740814 Bottom = 0.00017325 Done calling nodal solver Timestep 25 ends with TIME = 0.09103498113 DT = 0.006151576773 Timing summary: Advection :0.010712388 seconds MAC Proj :0.006027838 seconds Nodal Proj :0.011559243 seconds Reactions :0.033684013 seconds Misc :0.003456282 seconds Base State :5.600000019e-08 seconds Time to advance time step: 0.065573545 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 26 gives dt =1e+20 dt_growth factor limits the new dt = 0.006459155611  Timestep 26 starts with TIME = 0.09103498113 DT = 0.006459155611 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.231798942e-29 MLMG: Initial residual (resid0) = 9.231798942e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 7.720650071e-39, 8.363104655e-11 MLMG: Timers: Solve = 0.004777171 Iter = 0.004551758 Bottom = 0.000149815 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.231798942e-29 MLMG: Initial residual (resid0) = 7.720650071e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000229417 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 5.920048083e-19 MLMG: Initial residual (resid0) = 5.920048083e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.731567514e-29, 9.681623247e-11 MLMG: Timers: Solve = 0.010001491 Iter = 0.009744649 Bottom = 0.000145659 Done calling nodal solver Timestep 26 ends with TIME = 0.09749413674 DT = 0.006459155611 Timing summary: Advection :0.011058673 seconds MAC Proj :0.006056968 seconds Nodal Proj :0.011561193 seconds Reactions :0.033315219 seconds Misc :0.003457614 seconds Base State :6.000000008e-08 seconds Time to advance time step: 0.06558208 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 27 gives dt =1e+20 dt_growth factor limits the new dt = 0.006782113392  Timestep 27 starts with TIME = 0.09749413674 DT = 0.006782113392 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 9.693542528e-29 MLMG: Initial residual (resid0) = 9.693542528e-29 MLMG: Final Iter. 10 resid, resid/bnorm = 8.107279528e-39, 8.363587929e-11 MLMG: Timers: Solve = 0.004845457 Iter = 0.004618563 Bottom = 0.000161289 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 9.693542528e-29 MLMG: Initial residual (resid0) = 8.107279528e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000231195 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.216050487e-19 MLMG: Initial residual (resid0) = 6.216050487e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.01816515e-29, 9.68165423e-11 MLMG: Timers: Solve = 0.009935267 Iter = 0.00967816 Bottom = 0.000144775 Done calling nodal solver Timestep 27 ends with TIME = 0.1042762501 DT = 0.006782113392 Timing summary: Advection :0.011067381 seconds MAC Proj :0.006136561 seconds Nodal Proj :0.011494363 seconds Reactions :0.033275187 seconds Misc :0.003457332 seconds Base State :5.299999994e-08 seconds Time to advance time step: 0.065587812 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 28 gives dt =1e+20 dt_growth factor limits the new dt = 0.007121219061  Timestep 28 starts with TIME = 0.1042762501 DT = 0.007121219061 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.017816244e-28 MLMG: Initial residual (resid0) = 1.017816244e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 8.513151615e-39, 8.364134156e-11 MLMG: Timers: Solve = 0.005052454 Iter = 0.004574529 Bottom = 0.000146251 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.017816244e-28 MLMG: Initial residual (resid0) = 8.513151615e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000228773 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.526853012e-19 MLMG: Initial residual (resid0) = 6.526853012e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.319062814e-29, 9.681638001e-11 MLMG: Timers: Solve = 0.009898621 Iter = 0.009649311 Bottom = 0.000143639 Done calling nodal solver Timestep 28 ends with TIME = 0.1113974692 DT = 0.007121219061 Timing summary: Advection :0.010748222 seconds MAC Proj :0.006323146 seconds Nodal Proj :0.011454888 seconds Reactions :0.033341934 seconds Misc :0.003480678 seconds Base State :6.099999972e-08 seconds Time to advance time step: 0.065485531 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 29 gives dt =1e+20 dt_growth factor limits the new dt = 0.007477280014  Timestep 29 starts with TIME = 0.1113974692 DT = 0.007477280014 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.068706455e-28 MLMG: Initial residual (resid0) = 1.068706455e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 8.93776747e-39, 8.363164115e-11 MLMG: Timers: Solve = 0.005110555 Iter = 0.004883377 Bottom = 0.000171094 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.068706455e-28 MLMG: Initial residual (resid0) = 8.93776747e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000233069 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 6.853195662e-19 MLMG: Initial residual (resid0) = 6.853195662e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.635001992e-29, 9.681617626e-11 MLMG: Timers: Solve = 0.009908854 Iter = 0.009652888 Bottom = 0.000142495 Done calling nodal solver Timestep 29 ends with TIME = 0.1188747492 DT = 0.007477280014 Timing summary: Advection :0.010742233 seconds MAC Proj :0.00641161 seconds Nodal Proj :0.011454775 seconds Reactions :0.033308634 seconds Misc :0.003460654 seconds Base State :5.799999991e-08 seconds Time to advance time step: 0.065529964 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 30 gives dt =1e+20 dt_growth factor limits the new dt = 0.007851144015  Timestep 30 starts with TIME = 0.1188747492 DT = 0.007851144015 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.122134519e-28 MLMG: Initial residual (resid0) = 1.122134519e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 9.385420673e-39, 8.363899792e-11 MLMG: Timers: Solve = 0.005099249 Iter = 0.004868265 Bottom = 0.000168765 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.122134519e-28 MLMG: Initial residual (resid0) = 9.385420673e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.000258304 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.195855445e-19 MLMG: Initial residual (resid0) = 7.195855445e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.966772314e-29, 9.681645729e-11 MLMG: Timers: Solve = 0.009607006 Iter = 0.009356409 Bottom = 0.000144926 Done calling nodal solver Timestep 30 ends with TIME = 0.1267258932 DT = 0.007851144015 Timing summary: Advection :0.010765318 seconds MAC Proj :0.006424152 seconds Nodal Proj :0.011198635 seconds Reactions :0.03344742 seconds Misc :0.003443372 seconds Base State :5.700000028e-08 seconds Time to advance time step: 0.065421002 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 31 gives dt =1e+20 dt_growth factor limits the new dt = 0.008243701216  Timestep 31 starts with TIME = 0.1267258932 DT = 0.008243701216 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.17823894e-28 MLMG: Initial residual (resid0) = 1.17823894e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 9.854306349e-39, 8.363589098e-11 MLMG: Timers: Solve = 0.005047683 Iter = 0.004819356 Bottom = 0.000143536 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.17823894e-28 MLMG: Initial residual (resid0) = 9.854306349e-39 MLMG: No iterations needed MLMG: Timers: Solve = 0.00022312 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.555648218e-19 MLMG: Initial residual (resid0) = 7.555648218e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.315076744e-29, 9.681600484e-11 MLMG: Timers: Solve = 0.009606529 Iter = 0.009354818 Bottom = 0.00014266 Done calling nodal solver Timestep 31 ends with TIME = 0.1349695944 DT = 0.008243701216 Timing summary: Advection :0.010743725 seconds MAC Proj :0.006325314 seconds Nodal Proj :0.011206117 seconds Reactions :0.033404334 seconds Misc :0.003429354 seconds Base State :6.600000013e-08 seconds Time to advance time step: 0.06525281 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 32 gives dt =1e+20 dt_growth factor limits the new dt = 0.008655886277  Timestep 32 starts with TIME = 0.1349695944 DT = 0.008655886277 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.237154962e-28 MLMG: Initial residual (resid0) = 1.237154962e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 1.034785488e-38, 8.364235036e-11 MLMG: Timers: Solve = 0.005054356 Iter = 0.004832801 Bottom = 0.000145132 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.237154962e-28 MLMG: Initial residual (resid0) = 1.034785488e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000236888 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 7.933430629e-19 MLMG: Initial residual (resid0) = 7.933430629e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 7.680849359e-29, 9.681624154e-11 MLMG: Timers: Solve = 0.009601963 Iter = 0.009341188 Bottom = 0.000146505 Done calling nodal solver Timestep 32 ends with TIME = 0.1436254807 DT = 0.008655886277 Timing summary: Advection :0.010798362 seconds MAC Proj :0.006363369 seconds Nodal Proj :0.011148132 seconds Reactions :0.03348655 seconds Misc :0.003465209 seconds Base State :3.199999998e-08 seconds Time to advance time step: 0.065405221 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 33 gives dt =1e+20 dt_growth factor limits the new dt = 0.00908868059  Timestep 33 starts with TIME = 0.1436254807 DT = 0.00908868059 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.299018537e-28 MLMG: Initial residual (resid0) = 1.299018537e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 1.086569632e-38, 8.364542931e-11 MLMG: Timers: Solve = 0.00510305 Iter = 0.004875115 Bottom = 0.000146685 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.299018537e-28 MLMG: Initial residual (resid0) = 1.086569632e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000236729 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.33010216e-19 MLMG: Initial residual (resid0) = 8.33010216e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.064870161e-29, 9.681598144e-11 MLMG: Timers: Solve = 0.009610875 Iter = 0.009360173 Bottom = 0.000142129 Done calling nodal solver Timestep 33 ends with TIME = 0.1527141613 DT = 0.00908868059 Timing summary: Advection :0.011172471 seconds MAC Proj :0.006393256 seconds Nodal Proj :0.011167829 seconds Reactions :0.033474742 seconds Misc :0.003430604 seconds Base State :6.399999997e-08 seconds Time to advance time step: 0.065775081 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 34 gives dt =1e+20 dt_growth factor limits the new dt = 0.00954311462  Timestep 34 starts with TIME = 0.1527141613 DT = 0.00954311462 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.36395792e-28 MLMG: Initial residual (resid0) = 1.36395792e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 1.140766812e-38, 8.363651071e-11 MLMG: Timers: Solve = 0.004750296 Iter = 0.004524081 Bottom = 0.000144142 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.36395792e-28 MLMG: Initial residual (resid0) = 1.140766812e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000231281 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 8.746607268e-19 MLMG: Initial residual (resid0) = 8.746607268e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 8.468102113e-29, 9.681584932e-11 MLMG: Timers: Solve = 0.009586788 Iter = 0.009328856 Bottom = 0.000145137 Done calling nodal solver Timestep 34 ends with TIME = 0.1622572759 DT = 0.00954311462 Timing summary: Advection :0.011368755 seconds MAC Proj :0.006130291 seconds Nodal Proj :0.011147229 seconds Reactions :0.033469351 seconds Misc :0.00343785 seconds Base State :5.199999986e-08 seconds Time to advance time step: 0.065686748 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 35 gives dt =1e+20 dt_growth factor limits the new dt = 0.01002027035  Timestep 35 starts with TIME = 0.1622572759 DT = 0.01002027035 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.432155932e-28 MLMG: Initial residual (resid0) = 1.432155932e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 1.198039562e-38, 8.365287148e-11 MLMG: Timers: Solve = 0.005065231 Iter = 0.004839556 Bottom = 0.000147185 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.432155932e-28 MLMG: Initial residual (resid0) = 1.198039562e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000228716 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.132275502e-19 MLMG: Initial residual (resid0) = 9.132275502e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 5.364177118e-29, 5.873866942e-11 MLMG: Timers: Solve = 0.009602814 Iter = 0.009343501 Bottom = 0.000145936 Done calling nodal solver Timestep 35 ends with TIME = 0.1722775463 DT = 0.01002027035 Timing summary: Advection :0.011138826 seconds MAC Proj :0.006352393 seconds Nodal Proj :0.01116398 seconds Reactions :0.034489723 seconds Misc :0.003470775 seconds Base State :6.19999998e-08 seconds Time to advance time step: 0.06674313 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 36 gives dt =1e+20 dt_growth factor limits the new dt = 0.01052128387  Timestep 36 starts with TIME = 0.1722775463 DT = 0.01052128387 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 4.305515288e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.231616576e-30, 5.183157942e-11 MLMG: Timers: Solve = 0.004754851 Iter = 0.004529017 Bottom = 0.000146098 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.305515288e-20 MLMG: Initial residual (resid0) = 2.231616576e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000230642 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.643134513e-19 MLMG: Initial residual (resid0) = 9.643134513e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 9.336118739e-29, 9.68162243e-11 MLMG: Timers: Solve = 0.009645329 Iter = 0.009387103 Bottom = 0.00014695 Done calling nodal solver Timestep 36 ends with TIME = 0.1827988301 DT = 0.01052128387 Timing summary: Advection :0.011427367 seconds MAC Proj :0.006034411 seconds Nodal Proj :0.011207288 seconds Reactions :0.033590509 seconds Misc :0.003472767 seconds Base State :5.299999994e-08 seconds Time to advance time step: 0.065859628 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 37 gives dt =1e+20 dt_growth factor limits the new dt = 0.01104734806  Timestep 37 starts with TIME = 0.1827988301 DT = 0.01104734806 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.961609573e-28 MLMG: Initial residual (resid0) = 1.961609573e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 1.59094123e-38, 8.110386758e-11 MLMG: Timers: Solve = 0.004754465 Iter = 0.004525397 Bottom = 0.000146915 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.961609573e-28 MLMG: Initial residual (resid0) = 1.59094123e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000236445 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 9.618322872e-19 MLMG: Initial residual (resid0) = 9.618322872e-19 MLMG: Final Iter. 9 resid, resid/bnorm = 6.074575638e-29, 6.315628741e-11 MLMG: Timers: Solve = 0.009588212 Iter = 0.009338545 Bottom = 0.000146637 Done calling nodal solver Timestep 37 ends with TIME = 0.1938461782 DT = 0.01104734806 Timing summary: Advection :0.011481414 seconds MAC Proj :0.006073428 seconds Nodal Proj :0.011414856 seconds Reactions :0.033099675 seconds Misc :0.003482812 seconds Base State :3.300000007e-08 seconds Time to advance time step: 0.065689366 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 38 gives dt =1e+20 dt_growth factor limits the new dt = 0.01159971547  Timestep 38 starts with TIME = 0.1938461782 DT = 0.01159971547 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 4.746830605e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 2.490639479e-30, 5.246952518e-11 MLMG: Timers: Solve = 0.004761689 Iter = 0.004530836 Bottom = 0.000144437 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 4.746830605e-20 MLMG: Initial residual (resid0) = 2.490639479e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000442248 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.06315558e-18 MLMG: Initial residual (resid0) = 1.06315558e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.029308444e-28, 9.681635155e-11 MLMG: Timers: Solve = 0.009612089 Iter = 0.009345265 Bottom = 0.00014401 Done calling nodal solver Timestep 38 ends with TIME = 0.2054458937 DT = 0.01159971547 Timing summary: Advection :0.01129632 seconds MAC Proj :0.006290663 seconds Nodal Proj :0.011328666 seconds Reactions :0.033039478 seconds Misc :0.003453955 seconds Base State :6.600000013e-08 seconds Time to advance time step: 0.065530455 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 39 gives dt =1e+20 dt_growth factor limits the new dt = 0.01217970124  Timestep 39 starts with TIME = 0.2054458937 DT = 0.01217970124 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.14525299e-28 MLMG: Initial residual (resid0) = 2.14525299e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 1.741544942e-38, 8.118133154e-11 MLMG: Timers: Solve = 0.004741468 Iter = 0.004515958 Bottom = 0.000142339 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.14525299e-28 MLMG: Initial residual (resid0) = 1.741544942e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000227885 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.116313359e-18 MLMG: Initial residual (resid0) = 1.116313359e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.080770255e-28, 9.681602807e-11 MLMG: Timers: Solve = 0.009609855 Iter = 0.009347429 Bottom = 0.000146044 Done calling nodal solver Timestep 39 ends with TIME = 0.2176255949 DT = 0.01217970124 Timing summary: Advection :0.011779316 seconds MAC Proj :0.006034846 seconds Nodal Proj :0.011166876 seconds Reactions :0.033016375 seconds Misc :0.003470041 seconds Base State :5.600000019e-08 seconds Time to advance time step: 0.065600959 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 40 gives dt =1e+20 dt_growth factor limits the new dt = 0.0127886863  Timestep 40 starts with TIME = 0.2176255949 DT = 0.0127886863 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.829937332e-28 MLMG: Initial residual (resid0) = 1.829937332e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 1.528823351e-38, 8.354512059e-11 MLMG: Timers: Solve = 0.00473409 Iter = 0.004509021 Bottom = 0.000144264 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.829937332e-28 MLMG: Initial residual (resid0) = 1.528823351e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000226012 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.172129027e-18 MLMG: Initial residual (resid0) = 1.172129027e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.134813775e-28, 9.681645528e-11 MLMG: Timers: Solve = 0.009867395 Iter = 0.009404615 Bottom = 0.000144534 Done calling nodal solver Timestep 40 ends with TIME = 0.2304142812 DT = 0.0127886863 Timing summary: Advection :0.011078344 seconds MAC Proj :0.006022271 seconds Nodal Proj :0.011428892 seconds Reactions :0.0330934 seconds Misc :0.003771467 seconds Base State :4.699999989e-08 seconds Time to advance time step: 0.065519739 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 41 gives dt =1e+20 dt_growth factor limits the new dt = 0.01342812062  Timestep 41 starts with TIME = 0.2304142812 DT = 0.01342812062 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 1.919306124e-28 MLMG: Initial residual (resid0) = 1.919306124e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 1.605052866e-38, 8.362672563e-11 MLMG: Timers: Solve = 0.004752473 Iter = 0.004516425 Bottom = 0.000142398 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 1.919306124e-28 MLMG: Initial residual (resid0) = 1.605052866e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000537264 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.230735478e-18 MLMG: Initial residual (resid0) = 1.230735478e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.191553597e-28, 9.681638486e-11 MLMG: Timers: Solve = 0.009636673 Iter = 0.009375172 Bottom = 0.000145814 Done calling nodal solver Timestep 41 ends with TIME = 0.2438424018 DT = 0.01342812062 Timing summary: Advection :0.014051412 seconds MAC Proj :0.006525719 seconds Nodal Proj :0.011199173 seconds Reactions :0.034577264 seconds Misc :0.004078065 seconds Base State :9.700000003e-08 seconds Time to advance time step: 0.070587033 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 42 gives dt =1e+20 dt_growth factor limits the new dt = 0.01409952665  Timestep 42 starts with TIME = 0.2438424018 DT = 0.01409952665 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.015138921e-28 MLMG: Initial residual (resid0) = 2.015138921e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 1.685470583e-38, 8.364041632e-11 MLMG: Timers: Solve = 0.004867577 Iter = 0.004631198 Bottom = 0.000145528 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.015138921e-28 MLMG: Initial residual (resid0) = 1.685470583e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000229949 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.292272252e-18 MLMG: Initial residual (resid0) = 1.292272252e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.251128388e-28, 9.681616131e-11 MLMG: Timers: Solve = 0.009584033 Iter = 0.009328619 Bottom = 0.000144763 Done calling nodal solver Timestep 42 ends with TIME = 0.2579419285 DT = 0.01409952665 Timing summary: Advection :0.011082211 seconds MAC Proj :0.006303185 seconds Nodal Proj :0.011138237 seconds Reactions :0.033451594 seconds Misc :0.003492784 seconds Base State :6.000000008e-08 seconds Time to advance time step: 0.065608831 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 43 gives dt =1e+20 dt_growth factor limits the new dt = 0.01480450298  Timestep 43 starts with TIME = 0.2579419285 DT = 0.01480450298 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.115965176e-28 MLMG: Initial residual (resid0) = 2.115965176e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 1.769628084e-38, 8.36321932e-11 MLMG: Timers: Solve = 0.00475191 Iter = 0.004522533 Bottom = 0.000142007 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.115965176e-28 MLMG: Initial residual (resid0) = 1.769628084e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000234607 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.356885865e-18 MLMG: Initial residual (resid0) = 1.356885865e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.313690297e-28, 9.681656583e-11 MLMG: Timers: Solve = 0.009605679 Iter = 0.009345976 Bottom = 0.000142615 Done calling nodal solver Timestep 43 ends with TIME = 0.2727464314 DT = 0.01480450298 Timing summary: Advection :0.011337629 seconds MAC Proj :0.006049791 seconds Nodal Proj :0.01120731 seconds Reactions :0.033458009 seconds Misc :0.00345144 seconds Base State :6.299999988e-08 seconds Time to advance time step: 0.065644849 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 44 gives dt =1e+20 dt_growth factor limits the new dt = 0.01554472813  Timestep 44 starts with TIME = 0.2727464314 DT = 0.01554472813 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.221714365e-28 MLMG: Initial residual (resid0) = 2.221714365e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 1.858144184e-38, 8.363560203e-11 MLMG: Timers: Solve = 0.004751241 Iter = 0.00452298 Bottom = 0.000145024 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.221714365e-28 MLMG: Initial residual (resid0) = 1.858144184e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000338557 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.424730158e-18 MLMG: Initial residual (resid0) = 1.424730158e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.379372211e-28, 9.681638334e-11 MLMG: Timers: Solve = 0.009602059 Iter = 0.009348486 Bottom = 0.000144591 Done calling nodal solver Timestep 44 ends with TIME = 0.2882911596 DT = 0.01554472813 Timing summary: Advection :0.011079705 seconds MAC Proj :0.006299859 seconds Nodal Proj :0.011530904 seconds Reactions :0.033174069 seconds Misc :0.003458896 seconds Base State :3.300000007e-08 seconds Time to advance time step: 0.065676199 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 45 gives dt =1e+20 dt_growth factor limits the new dt = 0.01632196453  Timestep 45 starts with TIME = 0.2882911596 DT = 0.01632196453 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.332816252e-28 MLMG: Initial residual (resid0) = 2.332816252e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 1.951160134e-38, 8.363968368e-11 MLMG: Timers: Solve = 0.004752711 Iter = 0.004521772 Bottom = 0.000143902 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.332816252e-28 MLMG: Initial residual (resid0) = 1.951160134e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.0002572 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.48755145e-18 MLMG: Initial residual (resid0) = 1.48755145e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 9.467081975e-29, 6.364204732e-11 MLMG: Timers: Solve = 0.009599557 Iter = 0.009341393 Bottom = 0.000143506 Done calling nodal solver Timestep 45 ends with TIME = 0.3046131241 DT = 0.01632196453 Timing summary: Advection :0.011599607 seconds MAC Proj :0.006168801 seconds Nodal Proj :0.011165946 seconds Reactions :0.033114511 seconds Misc :0.003477554 seconds Base State :5.900000044e-08 seconds Time to advance time step: 0.065668871 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 46 gives dt =1e+20 dt_growth factor limits the new dt = 0.01713806276  Timestep 46 starts with TIME = 0.3046131241 DT = 0.01713806276 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 7.013230718e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.387147673e-30, 4.829653849e-11 MLMG: Timers: Solve = 0.004754026 Iter = 0.004525011 Bottom = 0.000144177 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 7.013230718e-20 MLMG: Initial residual (resid0) = 3.387147673e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.000236245 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.570764999e-18 MLMG: Initial residual (resid0) = 1.570764999e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.520748951e-28, 9.681581595e-11 MLMG: Timers: Solve = 0.009608557 Iter = 0.009352579 Bottom = 0.000142465 Done calling nodal solver Timestep 46 ends with TIME = 0.3217511869 DT = 0.01713806276 Timing summary: Advection :0.011792622 seconds MAC Proj :0.006053589 seconds Nodal Proj :0.011232485 seconds Reactions :0.033135667 seconds Misc :0.003461772 seconds Base State :3.600000031e-08 seconds Time to advance time step: 0.065809389 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 47 gives dt =1e+20 dt_growth factor limits the new dt = 0.0179949659  Timestep 47 starts with TIME = 0.3217511869 DT = 0.0179949659 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 3.116225903e-28 MLMG: Initial residual (resid0) = 3.116225903e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 2.535948889e-38, 8.137885275e-11 MLMG: Timers: Solve = 0.00475639 Iter = 0.004532201 Bottom = 0.000146935 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 3.116225903e-28 MLMG: Initial residual (resid0) = 2.535948889e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000232218 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.649303249e-18 MLMG: Initial residual (resid0) = 1.649303249e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.596796221e-28, 9.681641149e-11 MLMG: Timers: Solve = 0.009890713 Iter = 0.009487303 Bottom = 0.00014503 Done calling nodal solver Timestep 47 ends with TIME = 0.3397461528 DT = 0.0179949659 Timing summary: Advection :0.011108971 seconds MAC Proj :0.006030971 seconds Nodal Proj :0.011457532 seconds Reactions :0.033193007 seconds Misc :0.0037597 seconds Base State :3.09999999e-08 seconds Time to advance time step: 0.065678106 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 48 gives dt =1e+20 dt_growth factor limits the new dt = 0.01889471419  Timestep 48 starts with TIME = 0.3397461528 DT = 0.01889471419 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.703348136e-28 MLMG: Initial residual (resid0) = 2.703348136e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 2.258606139e-38, 8.354847489e-11 MLMG: Timers: Solve = 0.004757002 Iter = 0.00452885 Bottom = 0.00014395 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.703348136e-28 MLMG: Initial residual (resid0) = 2.258606139e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000240822 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.731768412e-18 MLMG: Initial residual (resid0) = 1.731768412e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.676627943e-28, 9.68159444e-11 MLMG: Timers: Solve = 0.009838817 Iter = 0.00958284 Bottom = 0.000143877 Done calling nodal solver Timestep 48 ends with TIME = 0.358640867 DT = 0.01889471419 Timing summary: Advection :0.011233831 seconds MAC Proj :0.006060334 seconds Nodal Proj :0.011403288 seconds Reactions :0.033114281 seconds Misc :0.003766792 seconds Base State :3.09999999e-08 seconds Time to advance time step: 0.065710052 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 49 gives dt =1e+20 dt_growth factor limits the new dt = 0.0198394499  Timestep 49 starts with TIME = 0.358640867 DT = 0.0198394499 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 2.835670205e-28 MLMG: Initial residual (resid0) = 2.835670205e-28 MLMG: Final Iter. 10 resid, resid/bnorm = 2.371553037e-38, 8.363289329e-11 MLMG: Timers: Solve = 0.006432192 Iter = 0.006197644 Bottom = 0.00024339 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 2.835670205e-28 MLMG: Initial residual (resid0) = 2.3715351e-38 MLMG: No iterations needed MLMG: Timers: Solve = 0.000230272 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.909401067e-18 MLMG: Initial residual (resid0) = 1.909401067e-18 MLMG: Final Iter. 10 resid, resid/bnorm = 2.383858307e-29, 1.248484851e-11 MLMG: Timers: Solve = 0.010630903 Iter = 0.010366897 Bottom = 0.000160695 Done calling nodal solver Timestep 49 ends with TIME = 0.3784803169 DT = 0.0198394499 Timing summary: Advection :0.012231125 seconds MAC Proj :0.007860084 seconds Nodal Proj :0.012185131 seconds Reactions :0.033176926 seconds Misc :0.003618395 seconds Base State :5.600000019e-08 seconds Time to advance time step: 0.069214188 Call to estdt for level 0 gives dt_lev = 1e+50 Minimum estdt over all levels = 1e+20 Call to estdt at beginning of step 50 gives dt =1e+20 dt_growth factor limits the new dt = 0.0208314224  Timestep 50 starts with TIME = 0.3784803169 DT = 0.0208314224 Cell Count: Level 0, 16384 cells inner sponge: r_sp , r_tp : 9609375000, 9609375000 <<< STEP 1 : react state >>> <<< STEP 2 : make w0 >>> <<< STEP 3 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 8.242756114e-20 MLMG: Final Iter. 10 resid, resid/bnorm = 3.780853259e-30, 4.586879931e-11 MLMG: Timers: Solve = 0.004751095 Iter = 0.004525294 Bottom = 0.000143959 <<< STEP 4 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 4a: thermal conduct >>> <<< STEP 5 : react state >>> <<< STEP 6 : make new S and new w0 >>> <<< STEP 7 : create MAC velocities >>> MLMG: Initial rhs = 8.242756114e-20 MLMG: Initial residual (resid0) = 3.780853259e-30 MLMG: No iterations needed MLMG: Timers: Solve = 0.00053645 Iter = 0 Bottom = 0 <<< STEP 8 : advect base >>> : density_advance >>> : tracer_advance >>> : enthalpy_advance >>> <<< STEP 8a: thermal conduct >>> <<< STEP 9 : react state >>> <<< STEP 10: make new S >>> <<< STEP 11: update and project new velocity >>> Calling nodal solver MLMG: Initial rhs = 1.909274674e-18 MLMG: Initial residual (resid0) = 1.909274674e-18 MLMG: Final Iter. 9 resid, resid/bnorm = 1.848494079e-28, 9.681656099e-11 MLMG: Timers: Solve = 0.009623314 Iter = 0.009361284 Bottom = 0.00014167 Done calling nodal solver Timestep 50 ends with TIME = 0.3993117393 DT = 0.0208314224 Timing summary: Advection :0.011431942 seconds MAC Proj :0.006331043 seconds Nodal Proj :0.011544714 seconds Reactions :0.033193967 seconds Misc :0.00347576 seconds Base State :5.099999978e-08 seconds Time to advance time step: 0.066114482 Writing plotfile 50 inner sponge: r_sp , r_tp : 9609375000, 9609375000 Time to write plotfile: 0.024034967 Writing checkpoint 50 Writing checkpoint chk0000050 Total Time: 4.479082576 Unused ParmParse Variables: [TOP]::amr.check_file(nvals = 1) :: [test_stability_2d_chk] [TOP]::amr.checkpoint_files_output(nvals = 1) :: [0] [TOP]::amr.plot_file(nvals = 1) :: [test_stability_2d_plt] AMReX (26.10-92-gec6902bd5e2b) finalized